Lug Nut Recommendation for a 1/2 inch Studs on Kodiak Disc Brake Kit
Updated 03/10/2015 | Published 03/09/2015
Products Featured in This Question
Question:
we have the Kodiak disc brake kit that came with 1/2 inch studs. our trailer has 9/16 studs. can we use our same wheels on the 1/2 inch studs?? and if we can what type of lug nuts should we buy. they are aluminum wheels on our 2015 bighorn.?? or should we start over with the 9/16 kit?? thanks
asked by: Jeff
Expert Reply:
The taper of the lug nuts should take up the .062 difference between the 9/16 inch hole and the 1/2 inch wheel stud, allowing the lug nuts to tighten with no problem.
For acorn nuts to fit a 9/16 inch stud you would want the part # 12CLN, or for an open nut you would want part # CE11051. Either of these would work fine for you.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly - 5,200-lb, 6,000-lb and 7,000-lb Axles - 12" - 8 on 6-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- 25580 / 14125A
- Standard Grade
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 1/2 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Continue Researching
- Search Results: dexter caliper
- Shop: DeeMaxx Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 10" Hub/Rotor - 5 on 4-1/2 - 3.5K
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Stainless Steel - 3,500 lbs
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and Stainless Steel - 3,500 lbs
- Q&A: Replacement Brake Calipers and Mounting Brackets for Load Rite Tandem Axle Trailer with 3.5K Alxes
- Shop: Replacement Mounting Bracket for Kodiak Disc Brake Caliper - Dacromet - 3,500 lbs
- Shop: DeeMaxx Disc Brake Kit w/ Actuator for Triple Axle Trailers - 10" Hub/Rotor - 5 on 4-1/2 - 3.5K
- Shop: Kodiak Trailer Hub for 3,500-lb Axles - 5 on 4-1/2 - Stainless Steel
- Video: All You Need to Know About the Kodiak Disc Brakes
- Q&A: Replacement Brake Pad and Rotor for Kodiak Stainless Steel 10" Disc Brake Kit
- Q&A: Stainless Steel Disc Brake Setup for Tie Down Engineering 3500 lb Axle
- Video: Replacement Mounting Bracket for Kodiak Disc Brake Caliper Review
- Video: Complete Breakdown of the Kodiak Disc Brake Kit-K2R35S
- Video: Hands-On with the Kodiak Trailer Hub for 3,500-lb Axles
- Q&A: Replacement Caliper for Tie Down Engineering 46802
- Q&A: Replacement Caliper Solution for Tie Down Engineering 46304
- Q&A: Replacement Master Cylinder Cap For Trailer Surge Brake Reservoir
- Video: What to Know About the Grease Seal
- Q&A: What Kodiak Brake Hardware is Compatible with Tie-Down Brakes on a Load Rite Trailer
- Video: Kodiak Disc Brake Kit: The Breakdown
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Search Results: trailer wiring
on Trailer Hubs and Drums
