Will the Replacement Handle Latch for Cam-Door Lock Part 158-102 Work With a Puck Style Padlock

Question

Question:

Does this hasp fit the puck style locks ?

asked by: Jeromy

0

Expert Reply:

Yes, the Replacement Handle Latch for Cam-Door Lock part # 158-102 will work with a puck style lock like the Master Lock Stainless Steel Padlock part # ML40D so long as the shackle does not exceed 1/2" diameter. I have attached a photo of this for you.

expert reply by: Conner L

0

click to enlarge

Answer 1

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 2

It does not, you would need to provide the hardware needed to attach the latch to the door. You'd want to find carriage bolts that would fit the latch as well as be appropriate for your trailer wall. The mounting hole dimensions are 5/16 by 5/16…

view full answer...

Answer 3

If you are wanting to go to higher capacity leaf springs I would advise against it. The problem is that since the trailer axle is rated for 3,500 pounds you won't gain any additional capacity by switching to higher capacity springs. What it will…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Will the Replacement Handle Latch for Cam-Door Lock Part 158-102 Work With a Puck Style Padlock

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching