Can Thule EasySnap Mounting Kit Parts be Pieced Out Individually

Question

Question:

Is it possible to order just 1 easy snap mounting bracket and not the complete kit?

asked by: John S

0

Expert Reply:

The Replacement EasySnap Mounting Kit for Thule Cargo Boxes # TH05820 comes from Thule in a kit and isn't able to be pieced out individually so if you need 1 replacement piece you will need to purchase the entire kit.

expert reply by: Jon G

0

Answer 1

To replace the mounting hardware for your Subaru/Thule Cargo box, you'll want to use the Replacement EasySnap Mounting Hardware #TH05820 . The U-bolts in this kit are 3-1/4 wide x 3" long x 1/4" diameter and will fit on most factory and…

view full answer...

Answer 2

You have the U-Bolts which have a rubber pad on them. That rubber pad will go underneath your crossbar and the two threaded ends will go through your cargo box holes. The stickers go on the holes that you're not using on the cargo box. The…

view full answer...

Answer 3

Yes, the Replacement EasySnap Mounting Kit part #TH05820 will fit your Thule Adventurer 650 Cargo Box but you might need to drill one new hole for each of the u-bolts but this will not affect anything with the box and it will be your only option if…

view full answer...

Answer 4

You can retrofit the older style Thule Box to fit aerodynamic bars with the EasySnap Mounting Kit for Thule Cargo Boxes #TH05820. However, the u-bolts that come with the EasySnap mounting kit may not fit the holes in your older box so you may need to…

view full answer...

Answer 5

For a Thule Evolution 1800 the mounting hardware is actually the EasySnap hardware which does not use knobs at all. Instead you'd need the EasySnap hardware kit part #TH05820 and you'd be set.

view full answer...

Answer 6

The replacement EasySnap Mounting Kit, part #TH05820 that you had looked at is compatible with your Evolution 1600 cargo box, as confirmed by Thule. I've linked to a video outlining what's included in the kit.

view full answer...

Answer 7

I have attached a photo for you that shows how to stop the brackets from sliding within the channel on a Thule Cascade XT Cargo Box. As you can see, there is a lever on the actual bracket which will stop it from sliding within the track once you line…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can Thule EasySnap Mounting Kit Parts be Pieced Out Individually

Featured Help Information

Miscellaneous Media

Continue Researching