Trailer Hitch that Fits 2002 Toyota Tundra with Towable Bumper

Question

Question:

Would the universal brake kit hook into the spare plug at the end of my bed on the drivers side. I will need a brake kit also for my 2002 Toyota Tundra SR5 extended cab with a 4.7 V8. Could you give the part number I need for this also.

asked by: Doug M

1

Helpful Expert Reply:

The Curt hitch part # 13184 is the correct hitch for your 2002 Toyota Tundra that has the towable bumper. This hitch has a towing capacity of 5,000 lb. I attached an install video for it for you to check out as well.

expert reply by: Jameson C

1

Doug M.

7/1/2019

Hey Jameson I want to buy the trailer hitch but I also need the electric brake installation kit that will plug into the blank plug at the back of my truck can you send me the part number for it and the trailer hitch please.

Jameson C.

7/1/2019

You will need to start with a 4-way (if you do not have one). For that you would want the # 118378. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well. For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is one of our best selling brake controller because of how well it works and how easy it is to setup.

Doug M.

7/3/2019

Would the universal brake kit hook into the spare plug at the end of my bed on the drivers side. I will need a brake kit also for my 2002 Toyota Tundra SR5 extended cab with a 4.7 V8. Could you give the part number I need for this also.

Jameson C.

7/3/2019

Are you wanting to install the 7-way in your truck's bed? If so that is possible with the 7-way of the # ETBC7. The P2 I mentioned in previous answer would be the brake controller you'd need.

Answer 1

Hey Mike! When you say you have the tow package option I'm assuming you have the factory hitch. None of the hitches will fit your Tundra as is since the factory hitch is tied into the rear bumper and bumper brackets. You will have to replace the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Trailer Hitch that Fits 2002 Toyota Tundra with Towable Bumper

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching