Troubleshooting Dutton Lainson Coupler Repair Kit Install That Doesn't Seem to Fit Ball Well
Updated 06/05/2019 | Published 06/04/2019
Products Featured in This Question
Question:
I had bought the trailer hitch repair kit and installed it on the trailer. The latch will not lock down on the ball when its in place. When adjusted to fit on the ball where I can lock the latch down the nut came off. I double checked the trailer and its a D-L 980-2. The repair kit specified it was a fit to replace this latch. Any tips or suggestions you can give to fix this problem would be helpful. Thanks
asked by: Matthew S
Expert Reply:
Are you possibly attempting to use the wrong diameter hitch ball with your coupler? The latch repair kit part # DL13970 that you referenced is the correct kit for your coupler but it is also designed for a 2 inch ball.
The part # DL13968 is a similar repair kit for versions of your coupler that fit a 1-7/8 inch ball.
That said, I attached an install video for you to check out for these repair kits to show you how they should install. Maybe this will help figure out if there's an issue with how yours was put together.
Product Page this Question was Asked From
Repair Kit for Dutton-Lainson Class II and III Couplers
- Accessories and Parts
- Straight Tongue Trailer Coupler
- Coupler Repair
- Dutton-Lainson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: trailer tires and wheels
- Search Results: coupler repair
- Shop: Kenda 5.30-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Shop: Loadstar ST175/80D13 Bias Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2
- Shop: Replacement Bearing Kit with Bearings L44649, Races L44610, Seal 10-9 - Fits 1.063" Spindles
- Shop: Trailer Hub Assembly - 2,200-lb E-Z Lube Axle - 5 on 4-1/2 - 13" - 15" Wheels - Galvanized
- Shop: Repair Kit for Dutton-Lainson Class II and III Couplers
- Shop: Trailer Wiring
- Search Results: coupler repair kit
- Search Results: fulton straight tongue trailer coupler
- Q&A: Is There A Repair Kit For Yoke Style Trailer Couplers?
- Q&A: Hand Wheel Coupler Replacement Recommendation
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Search Results: trailer jack
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Brake Controller
- Shop: Gooseneck Hitch
on Accessories and Parts
