How To Transfer the Tekonsha Prodigy P2 From a 2001 Ford F-150 to a 2018 Ford F-150

Question

Question:

I have a Prodigy P2 in my 2001 Ford F-150. Will it install in my 2018 Ford f15

asked by: Chuck A

0

Expert Reply:

Yes, you can install the Tekonsha Prodigy P2 Trailer Brake Controller part # 90885 from your 2001 Ford F-150 on your 2018 Ford F-150 you just need an adapter, the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 22292.If you didn't grab the bracket from the old vehicle then you will also need the Replacement Mounting Bracket for Tekonsha Prodigy and P2 part # P7685.

expert reply by: Conner L

0

Answer 1

Since the 2019 Ford F-150 doesn't have any trailer wiring you'd need to first start with a 4-way with part #18252 and then use a 7-way adapter part #37185 and you'd be set. If the trailer has brakes instead you'd need the #ETBC7 for…

view full answer...

Answer 2

To install a brake controller on your 2017 Ford F-150 w/ factory tow package and 4-way connector, you will need to install Adapter 4 Pole to 7 Pole, part #37185. You will need to run 2 wires, to the front of the truck, the Black wire for 12 volt…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

According to Tekonsha who makes the brake controller install harness part #TK78VR that fits your 2022 Hyundai Palisade the brake controller install harness is behind the drivers side kick panel near where you left foot would be if you were driving.…

view full answer...

Answer 5

There is a bit of wiring needed to convert the 4-way of your F-150 to a 7-way but it's not too bad. First lets start with a brake controller though. For a brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This is our…

view full answer...

Answer 6

I did some digging and I cannot find any info on if there is a brake controller port under the dash of your truck. Doesn't mean there isn't one but I can't find any info on it or any other year F-650 as well. I'd be inclined to…

view full answer...

Answer 7

Hey Bill, yes you can install the Prodigy P2 brake controller part #90885 in your 2014 Ford F-150 with a factory 7-way without requiring any hardwiring. For that all you need is the part #22292 which plugs into the truck in a port under the dash.

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

If your 2019 Ford F-150 did not come from the factory with a 7 Way on the back of the vehicle, the needed power wire and brake signal wires may actually be there, but are not connected to the factory port. They can also be pretty hard to get at as…

view full answer...

Answer 10

The appropriate parts you need to transfer the Tekonsha Prodigy P2 #90885 to your 2019 Ford F-150 depend on if you have a factory 4-pole plug or a factory 7-way plug already installed. If you have a factory 4-way, you will need the following parts: -…

view full answer...

Answer 11

For a brake controller I would recommend the Prodigy P2 Brake Controller part #90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount…

view full answer...

Answer 12

To add a 7-way and brake controller to youd 2018 Ford F-150 that doesn't have the factory tow package you'll need to start with a 4-way (if you do not have one). For that you would want the #HM11140735. From there you would need to convert…

view full answer...

How To Transfer the Tekonsha Prodigy P2 From a 2001 Ford F-150 to a 2018 Ford F-150

Continue Researching