Replacement Bevel Gear Set for Happijac Square Tube Jack

Question

Question:

I have an older square tube Happijac with stripped gears on my pu camper. Will these gears work as replacements? Are they difficult to change out? Thank you

asked by: Jan

0

Expert Reply:

Yes, for your older Happijac square tube jacks the bevel gear set part # LC182851 is what you'll need. The install is pretty easy. It's basically just a matter of taking the jack apart and reinstalling it the same way you took it apart.

expert reply by: Jameson C

0

Answer 1

I took a look in the owner's manual for the HappiJac Camper Jack 4600 and found the following under maintenance which I have attached for you below. Therefore, no, it's not advised to completely disassemble the jack to service the screw per…

view full answer...

Answer 2

I've attached instructions to this question to give you a getter look at replacing the Bevel Gears #LC182851 in your HappiJac #LC736514 #LC736515. Unfortunately, I do not have a video for you but the instructions do provide good pictures. First…

view full answer...

Answer 3

What specifically are you looking for? The most commonly replaced component for a trailer jack is the bevel gears which the Replacement Bevel Gears #LC182851 you referenced are correct for that.

view full answer...

Answer 4

I reached out to the manufacturer who told me the Replacement Bevel Gears for HappiJac Truck Camper Jack System #LC182851 will fit and work on your HappiJac 4800 Series jack.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Bevel Gear Set for Happijac Square Tube Jack

Product Page this Question was Asked From

Continue Researching