Power To Brake Controller and Trailer Connector on a 2006 Chevy Silverado 2500 Cut Out
Updated 05/01/2019 | Published 04/30/2019 >
Products Featured in This Question
Question:
Hello, i have a 2006 chev 2500hd with tow package, last night i installed the tekonsha p3 controller, plugged it into the proper spot on fuse panel, i noted it power up briefly while truck was off, then went out. i turned key on and no power is coming to the module. incidentally , when i plug my trailer into the truck, all marker lights, signal lights work, but there is no power to the trailer to open slides and other items. i checked the appropiate fuse under the hood and it looks good, however i havent tested it yet, any suggestions?
asked by: Kelly T
Expert Reply:
The power for the brake controller and trailer connector on your 2006 Chevrolet Silverado 2500HD is feed from two studs on the power distribution center (PDC) which is located under your hood, in the engine bay. The only thing that I can think of as to why both the power for the brake controller and trailer connector suddenly went out assuming there were no blown fuses is if the ring terminals on these studs somehow came loose. Therefore, you will want to check the flange nuts on both of these terminals to make sure they are securely attached. I have attached a photo of this process for you as well.
The only other option I have for you would be to just run your own power wire to the brake controller and trailer connector with part # 10-1-1 and part # DW05705-1.
Continue Researching
- Shop: Trailer Wiring
- Shop: Front Mount Hitch
- Shop: Trailer Hitch
- Shop: Vehicle Lights
- Search Results: 7 way plug
- Q&A: Trailer Hitch For 2007 Chevrolet Silverado 2500HD Classic
- Q&A: Curt Class V Trailer Hitch that Fits 2002 GMC Sierra 3500 Long Bed
- Q&A: Replacement 7-Way Wiring Pigtail for 2006 Chevy Silverado 2500
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Pacer Performance Hi-Five Truck Cab Light Kit - Chevy/GM - 3 Piece - White Bulbs - Amber Lens
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Pollak Black Plastic, 7-Pole, RV Blade-Style Trailer Socket - Vehicle End
- Shop: Pacer Performance Hi-Five LED Truck Cab Light Kit - Chevy/GM - 3 Piece - Amber LEDs - Amber Lens
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Q&A: Location of the 40-Amp Fuse for the 2006 Chevrolet Silverado Tow Package
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Q&A: No Power to Trailer Brake Controller Install on a 2006 Silverado 1500
- Q&A: No Power to Trailer Brakes with Brake Pedal on a 2006 Chevy Silverado 2500HD
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer tires and wheels
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Clean Up Your Trailer Wiring
