Weight Capacity of B and W Turnoverball 1105R

Question

Question:

I have a b w 1105r hitch but I have been unsuccessful at locating its capacity. Would you be able to supply me with that knowledge?

asked by: Walt G

0

Expert Reply:

The 1105R is no longer made but the kit that replaced it was the # BWGNRK1108 which has a 30k weight capacity. The 1105R has the same capacity.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 10

Hey Mark, thanks for writing in. I can definitely help you find the right gooseneck pin box for your Alliance, but I will tell you that typically, the height of the goosebox is very similar to the height of the pin box and 5th wheel hitch it is…

view full answer...

Answer 11

Hey Steven, yes the Curt gooseneck hitch part #C44NQ does fit your 2019 Ford F-250 that has the brackets on the frame rails already for the OEM gooseneck hitch.

view full answer...

Answer 12

Hey there Trace! There are parts of the steel brackets that come into contact with the aluminum bed on your new 2026 F350 Super Duty (congrats on the new truck by the way - those are super nice!). B&W says to use strips of polypropylene tape…

view full answer...

Weight Capacity of B and W Turnoverball 1105R

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching