How To Prevent Galvanic Corrosion When Installing B&W Turnover Gooseneck In 2026 F350 Super Duty
Updated 04/16/2026 | Published 04/10/2026
Question:
Hello. The instructions state to note Fords galvanic corrosion warning. Does this come in contact with the bottom of the bed? Pictures dont look like it does, but the instructions also state to lift up or pull up against the bed without deforming the bed. Just trying to plan to have something in case it does. thanks!
asked by: Trace
Expert Reply:
Hey there Trace!
There are parts of the steel brackets that come into contact with the aluminum bed on your new 2026 F350 Super Duty (congrats on the new truck by the way - those are super nice!). B&W says to use strips of polypropylene tape where it might make contact with the bed. They don't go into detail on where exactly, but you'll see when you install it (or a shop installs it) that some parts may contact the bed. Like I said, it's normally the brackets themselves.
Some other people said they put a strong layer or two of spray paint or rust-preventive spray paint from Rustoleum. I wasn't able to locate the TSB from Ford so maybe you can try on your end with your vin number, or by contacting a Ford dealer for more specific info on that front.
Let me know if there's anything else I can help you with! I'm here if you need me :)
Craig W.
4/16/2026
The short answer is there is no finer gooseneck hitch made. The only steel/aluminum contact is the two safety chain loops . The bed is coated with a galvanic inhibitor. The lifting into the drilled hole is a piece of cake. Just put a 2x6 across the bed rails then thread a tow strap through the bed hole and hitch hole, then use a wrench or screwdriver around the strap and crank it to the point of touch on the underside of the bed. My truck is a 2025 long box f-350 diesel. This is identical to the '26's. Attached is a picture after installation. The cable is just for the spare tire. Have fun! /Users/craigwilbur/Desktop/2025 BW underneath.jpeg
Product Page this Question was Asked From
B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Gooseneck Hitch
- Below the Bed
- Flip-Over Ball
- 7500 lbs TW
- 30000 lbs GTW
- Wheel Well Release
- Spring-Loaded Loop
- B and W
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Q&A: Will Curt T-Connector Vehicle Wiring Harness Fit 2025 Ford F-350
- Q&A: Are Inner Brackets of B and W Gooseneck Hitch Needed When Installing In 2026 Ford Truck
- Q&A: Correct Gen-Y Hitch Gooseneck Pin Box for 2025 Jayco Eagle 317ROLK
- Article: Gooseneck to 5th Wheel Adapters
- Q&A: Where Does The Red Wire Install to On the Roadmaster Brake-Lite Relay Kit 2007 Hummer H3
- Q&A: Will Gen-Y Hitch Nomad Gooseneck Pin Box Void Lippert Frame Warranty
- Q&A: B&W Turnoverball and Gooseneck Wiring for 2025 Ford F-250
- Article: Ram Trailer Tow Prep Package
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Converting Your RV Water Heater to Tankless
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: 5th Wheel to Gooseneck Adapters
Tom
4/16/2026
I had some pond liner material on hand so I glued a strip of that on the hitch before i pulled it up in place