Installation of Idler Hub on 7,000 lb EZ Lube Axle
Updated 03/04/2019 | Published 03/02/2019
Products Featured in This Question
Question:
Retainer clip instead of cotter pin How do you know how far to tighten the castle nut when you dont have the cotter pin whole as a reference? Im installing the hubs of a new 7000lb dexter ez lube axle
asked by: Kenn M
Expert Reply:
I took a look at the installation instructions in regards to using a the nut retainer as opposed to a cotter pin and it specifies:
"1) Finger tighten the nut until just snug ... Once in place the retainer/nut assembly should be free to move slightly. 2) If the nut is too tight, remove the the retainer and back the nut off approximately one twelfth of a turn and reinstall the retainer. The nut should now be free to move slightly."
Product Page this Question was Asked From
Dexter Trailer Axle Beam with E-Z Lube Spindles - 95" Long - 7,000 lbs
- Trailer Axles
- Leaf Spring Suspension
- Standard Grade
- No Hubs
- 7000 lbs
- Spindles Only
- 80 Inch Spring Center
- 95 Inch Hub Face
- No Drop or Lift
- Dexter
more information >
Continue Researching
- Search Results: seal driver
- Search Results: bunk carpet
- Search Results: winch
- Search Results: two speed winch trailer winch
- Search Results: dutton~lainson trailer winch
- Q&A: Replacement 3,500 lbs Axle for a Dexter w/a 93" Hub Face and 80" Spring Seat Spacing
- Shop: Bearing Buddy Bearing Protectors - Model 2441SS - Stainless Steel (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 2240SS - Stainless Steel (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 2328SS - Stainless Steel (Pair)
- Shop: Bearing Buddy Bearing Protectors - Model 2441T-SS - Threaded - Stainless Steel (Pair)
- Shop: Trailer Hitch
- Shop: 2-Speed Boat Trailer Winch with 20' Strap and Brake - 3,200 lbs
- Shop: Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,000 lbs
- Shop: EcoHitch Stealth Trailer Hitch Receiver - Custom Fit - 2"
- Search Results: trailer leaf springs
- Search Results: galvanized torsion axle
- Q&A: Difference Between 3 and 4 Leaf Spring Stack for 3,500 Pound Axle
- Q&A: Replacement Wheel Stud For Dexter 7000 lb Axle With 8 Lug Hub Assembly
- Video: Feature Review Replacement Nut Retainer for 6-191 Jam Nut
- Video: Complete Breakdown of the Dexter Trailer Springs Over-Under Conversion Kit
- Video: Hands-On with the Dexter Trailer Springs Over-Under Conversion Kit
- Video: Installation of the Dexter Trailer Axle Beam with E-Z Lube Spindles on a Trailer
- Video: Review of etrailer Trailer Hubs and Drums - Pre Greased Idler Hub - AKIHUB-865-7-2-EZ-K
- Video: Review of CE Smith Trailer Axles - Axle Spindle Parts - CES52QR
- Q&A: Replacement 7,000 lbs Dexter Axle w/ 95" Hub Face and 80" Spring Seat
- Q&A: Can Arms of B and W Replacement Base for Companion Flatbed Fifth Wheel be Turned Around
- Q&A: Solution for Needing Replacement Dexter Axle with Number 7658660 Part Number
- Q&A: Recommended Curt Helux Pin Box for a Rhino Bolt Pattern
- Article: Hydraulic Trailer Brakes: How They Work & What to Buy
- Article: Trailer Wiring Diagrams
on Trailer Axles
