2012 Nissan Pathfinder Brown Relay Install Location for Trailer Wiring

Question

Question:

Do you have a pic of where the Brown Trailer Tow relay goes that powers the 12 Volt circuit? thanks

asked by: Jeremy M

0

Expert Reply:

For the 2012 Pathfinders the relays are located under the hood. There should be a small black box, take the lid off of the box and there should be a legend that will tell you where each of the relays goes. See attached picture.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For your 2011 Nissan Pathfinder the running light relay #C57000 you mentioned is located behind the passenger side kick panel as shown in the included picture. This relay is a pretty common culprit to running lights not working on Nissan vehicles…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 8

For your 2024 Nissan Frontier I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like the Liberty because it is simple, reliable, and looks great in any vehicle. The main unit installs behind the dash, so only the control knob will…

view full answer...

Answer 9

Hey Brandon, I would strongly recommend sticking with the Tekonsha RF brake controller part #TK94FR. We know this works really well and it sounds like it worked well for you too. The Curt Echo is not reliable enough for me to really ever recommend it…

view full answer...

Answer 10

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

We can get you everything you need for towing with your 2017 Toyota Sienna XLE. By plastic shield, I believe you are referring to the appearance panel underneath the Sienna, and that will have to trimmed a bit in each of the hitches available for the…

view full answer...

2012 Nissan Pathfinder Brown Relay Install Location for Trailer Wiring

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching