Can an L68149 Bearing be Used to Replace an LM68149 Bearing

Question

Question:

What does the M stand for or mean LM68149? If it just says L68149 is it the same product? Thanks!

asked by: Mel

0

Expert Reply:

I am not quite sure what the M stands for but the # L68149 bearing will be an exact replacement for your LM68149 bearing. The M used to be used but was dropped as it became irrelevant in the part number side of things.

expert reply by: Jon G

0

Answer 1

We have the individual components of a bearing kit available for a Dexter 4,400 lb trailer axle but since it's a rarer axle capacity we don't have a bearing kit. So for a Timken set you'd want the part #TMK49FR and #TMK56FR and then for a…

view full answer...

Answer 2

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 3

Hey Rob; thanks for the photos and it was actually the one with the hub number that did it. That's a BD 545 which is an AxleTek 3,500 lb hub and drum like the Trailer Hub and Drum Assembly #AKHD-545-35-K. The 35 on the axle sticker was a good…

view full answer...

Answer 4

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Can an L68149 Bearing be Used to Replace an LM68149 Bearing

Product Page this Question was Asked From

Continue Researching