Availability of Vertical E-Track Where the Slots are Stacked On Top of Each Other

Question

Question:

Etrack seems to be well suited for a three-quarter inch plywood like there is in floors of trailers. But when it comes to wall mounting the vertical pieces are 3 and 1/2 inch thick typical trailer stud as one to 1 and 1/2 inches thick . We need a product that is designed just for the studs vertical mounting for box trailers . It should just look just like the single etrack only in one long strip. I could not find any of them anywhere maybe you can or suggest to the manufacturer

asked by: Brian

0

Expert Reply:

Sounds like you are looking for vertical E-track like the part # E19146. This is e track that is similar to the # SLSZ you referenced but with the tracks stacked on top of each other instead. The mounting holes are 2-3/4 inches apart from side to side and 2 inches apart vertically.

expert reply by: Jameson C

0

Answer 1

In the picture, the customer is using the Erickson tie-off ring #59131 with single E-track anchor, #SLSB. There is also a stainless model, #SLSS, and a zinc model, #SLSZ. If you want one you can paint yourself there is also an unfinished model,…

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

Since the slot dimensions and capacity of different brands of E-Track are identical, really the only differences are the finish and the lengths the tracks are sold in. If you're using the E-Track in an area where aesthetics are important, you can…

view full answer...

Answer 4

Hey Gary, thanks for the information! The etrailer Horizontal E Track item #e85VR would be a great way to add additional anchor points. You can bolt these tracks directly to your trailer's deck using self-drilling metal screws like item #SL99FR.…

view full answer...

Answer 5

I wouldn't recommend mounting the Erickson #EM77316 spare tire carrier on the door of an enclosed trailer. The carrier is meant to be installed inside an enclosed trailer, and is designed to hold the tire upright, not suspend it so the tire needs…

view full answer...

Answer 6

For a great method of holding your tools with the CargoSmart X-Track system, the best route is to go with the CargoSmart Landscape Tool Holder for E-Track and X-Track Systems - 200 lbs #3481741. These holders have a maximum weight capacity of 200…

view full answer...

Answer 7

You'll want to connect the black wire to a switch or circuit you can turn on and off for the Red Identification Light Bar with White LED Utility Light item #OPT88FR. If you wire it up like a standard light to a tail light wire the white utility…

view full answer...

Answer 8

Torque specs for wheel lug nuts vary depending on several factors like stud size, wheel size and wheel material. The linked image provides a listing of commonly recommended torque values. The studs on your hubs #A35RS545E are 1/2-inch diameter and…

view full answer...

Answer 9

Hello Josh, thanks for reaching out. The Self-Contained Hydraulic Jack #e33VV cannot be powered by the 7-way. It needs its own full size deep cycle RV/marine battery. You will also need battery cables for connecting to the HPU.

view full answer...

Answer 10

Hey Cheryl, Yes, the Self-Contained Hydraulic Jack #e33VV could be bolted the frame of your horse trailer to upgrade you to a motorized jack. This jack has a 12,000lb capacity so you'll want to verify what your pin weight is to ensure it falls…

view full answer...

Availability of Vertical E-Track Where the Slots are Stacked On Top of Each Other

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching