Draw-Tite 06623-099 Wt. Dist Hitch w/ Sway Control Chain Hangers

Question

Question:

I have a Draw-Tite 06623-099 Wt. Dist. hitch with sway control. I need the brackets that attach to the trailer frame. Can yo advise if these are available?

asked by: Jim B

0

Expert Reply:

For chain hangers or your Draw Tite weight distribution system we have the clamp on set part # RP58306 or we have the bolt on set part # RP58305. Either of these would work great with your Draw Tite system.

expert reply by: Jameson C

0

Draw Tite WD System
(click to enlarge)

Answer 1

To add a brake controller to your 2013 Ford E-350 I recommend installing the following: Curt T-Connector 4-Way - #C56020 Universal Wiring Kit - #ETBC7 Extra Wire - #10-2-1 Mounting Bracket - #18136 Primus IQ Brake Controller - #TK90160 The Curt…

view full answer...

Answer 2

Hi John; the Reese 06623-099 has been discontinued since 2011. In the past we have had someone successfully replace theirs using the #RP58167 but it will also require replacement spring bars since the ones you have now won't fit. If you let me…

view full answer...

Answer 3

I have a solution for you, but the bars you have aren't compatible with the current bar designs made so it's going to come down to you replacing the head and the bars of your setup. So for bars you would need the part #RP66009 which has the…

view full answer...

Answer 4

The weight distribution head you have was made obsolete on 2/10/2011. I spoke with my contact at Reese/Draw-Tite and the current springs bars will not fit the head that you have. In order to use new bars you would have to replace the whole system and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Draw-Tite 06623-099 Wt. Dist Hitch w/ Sway Control Chain Hangers

Continue Researching