Solution For Solera Manual Crank RV Head with Bad Gears

Question

Question:

When I try to crank my awning up the gears grind. Do you have replacement gears for manual solera awning?

asked by: Michael L

0

Expert Reply:

The best solution we have for your situation is a new manual crank drive head for your Solera manual awning since the gears aren't available. For that you'd want the black drive head part # LC300031.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You are going to need the Solera Awning Plain Drive Head Front Cover #LC289557 and Back Cover #LC289558 for your awning. Due to your covers being the oldest style that Lippert made they are no longer available and this is the updated cover. If you…

view full answer...

Answer 2

The gearbox inside of the Solera Manual Crank Style Awning Drive Head part #LC300031 is not available separately as a replacement part therefore if you need to replace this you will have choice but to replace the entire assembly.

view full answer...

Answer 3

When installing the Solera Manual Pull Style Awning Drive Head, Black #LC272067 you will want the spring to be under some tension when completing the installation so that it draws the awning back fully once you've completed the installation. My…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Solution For Solera Manual Crank RV Head with Bad Gears

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching