7-Way Trailer Wiring Recommendation for 2019 Honda Ridgeline

Question

Question:

Was looking for this t connector setup for a 2019 Honda Ridgeline RTL-E. Do u happen to have anything for my truck??

asked by: Thomas F

0

Expert Reply:

If you are looking for a 7-way trailer wiring connector for the rear of your 2019 Honda Ridgeline the correct part number is # 118288 which comes with everything needed to install on your vehicle. The # C56584 is a kit designed to plug inline with 7-way to provide a 5-way.

expert reply by: Jameson C

0

Answer 1

If you have the factory tow package or just installed the T-Connector Vehicle Wiring Harness #118288 on your 2021 Honda Ridgeline you will need to check the charge line fuse. According to page 564 of your owners manual I see there is a 20 amp fuse in…

view full answer...

Answer 2

The 2019 Honda Ridgeline is pre-wired to attach a 7-Way plug that powers trailer brakes but not all Honda Ridgelines have the wiring harness for a plug and play brake controller adapter. If you need a 7-way I recommend to use Tekonsha T-Connector…

view full answer...

Answer 3

Since your 2017 Honda Ridgeline has the factory 7-way connector on it you should have a wiring harness that has the standard to package plug. It's the harness that plugs into the back of the 7-way connector and looks like the picture I attached.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...