Recommended Skid Wheels for a 34' Coachmen Apex Ultra Lite Trailer

Question

Question:

Skids wheels for backing up steep driveway and going down steel driveway. Recommendation for a Coachmen 34 foot Apex Ultra Lite 300 BHS

asked by: Chris B

0

Expert Reply:

For your 34' Coachmen travel trailer I recommend installing weld-on rollers like part # UF48-979021 or # UF48-979023 to help protect your trailer while going up your driveway.

We do have some bolt-on options but they are meant for trailers or motorhomes that have hitches on them.

expert reply by: Jon G

0

click to enlarge

Answer 1

Skid wheels like the part #UF48-979021 that you referenced installed on the hitch and frame would be one solution to help prevent the dragging. While we don't have an air bag system we do have a lift kit part #RR23QX that will give you an…

view full answer...

Answer 2

You definitely can install the Ultra-Fab Skid Wheels #UF48-979013 on your 42' 5th wheel but it is worth noting that the wheel and caster plate measures 7-1/2" tall so if the 16-1/4" that you measured is from the frame rail then that…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Recommended Skid Wheels for a 34' Coachmen Apex Ultra Lite Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching