Best Way to Install a Recessed 4 Inch Round Tail Light on a Trailer
Updated 07/30/2018 | Published 07/28/2018
Products Featured in This Question
Question:
What is the EASIEST way to install a replacement round 4inch tail light? Light into the grommet and then in hole? What are the tricks to doing it easily ?
asked by: Ron
Expert Reply:
The best and easiest way to install a round 4" tail light like the Miro-Flex LED Trailer Stop/Turn/Tail Light part # STL23RB on a trailer would be to first clean the edges of the holes (no sharp metal) and then spray some soapy water on the gourmet while slipping it into place being careful not to tear the rubber. Once the grommet is in place you will then what to run the pigtail harness though the hole and plug it into the back of the light. Then you can then insert the tail light into the grommet.
If you need the correct grommet for this light then you can use part # A45GB and part # A45PB for the pigtail harness. I also highly recommend using part # DW05744-5 to join the wires together as they have heat shrink bodies which works to keep out dirt and moisture.
Product Page this Question was Asked From
Miro-Flex LED Trailer Light w/Reflector - Brake, Turn, Tail - Submersible - Round - Red - Clear Lens
- Trailer Lights
- Tail Lights
- Brake/Tail/Turn
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 4-5/16 Inch Diameter
- Red
- Optronics
more information >
Continue Researching
- Search Results: 4 inch round led trailer lights
- Search Results: wire nuts
- Search Results: wire connectors
- Shop: Rubber Grommet for 4" Round Trailer Lights - PVC
- Shop: Brophy Ball Mount - 3" Rise, 4" Drop - 14-5/8" Long - Aluminum - 8,000 lbs
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Pigtail - Qty 1
- Shop: Gooseneck Hitch
- Shop: Tri-Bar LED RV Tail Light - Stop, Tail, Turn - Submersible - 33 Diodes - Passenger's Side
- Video: In-Depth Review of the Trim Ring for Optronics UCL09 Series Trailer Utility Lights
- Video: A Closer Look at the LED Trailer Tail Light with Reflector
- Shop: TecNiq Tri Bar Heavy Duty ID Bar - 14.5" - Red Lens
- Shop: TecNiq Slim Profile Stop Tail Turn Reverse Light - 20" - Clear Lens
- Shop: TecNiq Low Profile ID Bar Light - Red - Surface Mount
- Q&A: How to Install Tail Light and Grommet into Trailer Light Mounting Bracket # BK70BB
- Q&A: What Size Hole Needs to Be Cut To Install the Sealed 4 inch Diameter Optronics Light STL42RB
- Q&A: 4 Inch Round Trailer Tail Light Cutout Size
- Q&A: Recommended Replacement For A Dometic 630515.331 AC Rooftop Unit
- Q&A: Replacement For TDE LP75 Disc Brake Actuator
- Q&A: Can Strap of Fulton XLT Powered Winch be Replaced
- Article: How to Winterize & De-Winterize Your RV (Simple Guide)
- Q&A: Replacement Passenger Side Miro-Flex LED Trailer Light 38 Diode
- Article: Trailer Wiring Diagrams
- Article: Holiday 2025 | Staff Picks for Real-Life Adventures
- Article: 5 Reasons to Convert Your RV Lights to LEDs Today
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Troubleshooting Brake Controller Installations
- Article: Trailer Lighting Requirements