Brake Controller and 7-Way Trailer Connector For 1995 Chevy C/K 1500
Published 06/28/2008
Products Featured in This Question
Question:
Can I get instructions on how to wire a 1995 Chevy 1500 for trailer breaks?
asked by: Jeremy
Expert Reply:
As a first step, you would need to select a brake controller. I would recommend the Tekonsha Prodigy P2, part # 90885. The P2 is extremely reliable and easy to use, which makes it one of our all-time best selling brake controllers.
Most of the Chevy trucks of that era had a blue and an orange or red wire ran along the frame rail for installing the controller. At the rear of the vehicle, they usually terminate on the end of the drivers side frame rail or above the spare tire. In the engine bay, the other end is located under the brake booster. The wires are wrapped in electrical tape, and can be a bit hard to locate. (See the video I have linked to for more details). The red or orange wire supplies 12-volt power to the trailer connector for any trailer mounted accessories that might require it. Attach this wire as shown in the video.
You will need a 7-way (part # 37185) adapter. If your truck already has the 4-pole connector, the existing connector would plug into the adapter. If you do not have an existing 4-pole, cut the connector off of the adapter and wire as shown in the video.
The controller itself would mount to the underside of the dash, usually to the right of the steering column within easy reach of the driver. The black wire from the controller would run through the firewall to the positive battery terminal via a 30-amp inline breaker, part # 38630. The white wire would attach to the negative battery terminal and the blue wire would attach to the blue wire located under the brake booster in the engine compartment. The red wire would access the brake stoplight signal. The brake stoplight switch is difficult to reach in the mid to late 1990s Chevy trucks, because the steering column is in the way. You can find this circuit in the main wiring harness as shown in the video, using a circuit tester like part # PTW2993 to locate the white wire that only shows voltage when the brake pedal is pressed. Or take a look at the fuse/relay block under the dash. If you have a spade terminal location that says NAT under it (there might be more than one), try using your tester on it while pressing the brake pedal. If this terminal shows voltage when the pedal is pressed, you can place a spade terminal on the end of that red brake controller wire and plug it in there.
I've linked you to some FAQ articles about brake controller installation that I hope you'll find helpful.
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Video: In-Depth Review of the Universal Installation Kit for Trailer Brake Controller
- Video: 1995 Chevrolet C/K Series Pickup Hitch Options
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: Recommended Brake Controller For A 1995 Chevrolet C/K Series Pickup
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Q&A: Brake Controller Install on 1995 Chevy C Series Pickup Truck
- Article: Brake Controller Installation: Starting from Scratch
- Article: Troubleshooting Brake Controller Installations
- Q&A: What Size Fuse or Circuit Breaker Should be Used for Brake Controller on a 2006 Chevrolet Silverado
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Q&A: Parts Needed to Install a Red Arc Brake Controller in a 2023 Toyota Tacoma
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Search Results: brake controller
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer brake controller
on Accessories and Parts
