Customers compare AKBRKR-S-10 to these similar products
Products Featured in this Video
Today we're going to take a look at the replacement electric trailer brake shoe and liner kit for a 10 inch brake assembly on 3,500 pound axles and this is for one wheel. Now, this part includes everything shown here, the 2 brake shoes, the 2 hold down springs, and the 2 pins. Now, these brake shoes and linings are for electric trailer brakes that are on 3,500 pound axles. On a brake assembly when… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Videos
Help Articles
Expert Answers
I reached out to Scamp for help to find your exact brakes, unfortunately due to the age of your 2000 Scamp 19 Everglades they did not have the exact information or parts available and the only thing that they could tell me is your trailer uses…
view full answer...I went out into our warehouse to measure the pad thickness of a Dexter 3,500 10 by 2-1/4 inch brake assembly like the part #23-468-469 and just the brake pad portion of the shoe measured .18 of an inch. The entire shoe thickness was .29 of an inch…
view full answer...Trailer electric brake magnets are non-polarized. When installing an electric brake assembly, like the Electric Trailer Brake Assembly, Left Hand #AKEBRK-35L, either wire can be used for the brake signal and the ground wire, it will not matter which…
view full answer...Yes, the Grease Seals 10-36 #RG06-070 that you referenced does have a garter spring as it is the exact same seal as your Dexter seal K71-305-00.
view full answer...It sounds like you are looking for 2 sets of left/right side brakes for your 7k trailer. If that is the case, we unfortuantely do not carry the 23-181-00 because these are an older brake model that was discontinued from Dexter. However, the new…
view full answer...A #84 spindle, like #TRU24FR , is a spindle for a 3,500 pound axle that has inner bearing #L68149 and outer bearing #L44649. The bearing kit that fits is #BK2-100. To replace your brakes and hubs you'll need the Kodiak Stainless Steel Brake Kit…
view full answer...On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.
view full answer...Normally a tandem axle trailer only has one brake wire going to the vehicle, and it is typically blue. If you have two separate brake wires for your axles, that is fine and will not cause an issue. Having one wire ran along the trailer instead of the…
view full answer...We do have brake shoes for a 3,500lb Dexter brake assembly, but the 12" x 2" is not going to work as you have 10" brakes. Instead you'll need the Dexter #K71-681 for the left side and #K71-682 for the right side if you have the…
view full answer...Bearing Buddy Bearing Protectors like #BB1781 have a spring loaded pressure in their design. There are times that this pressure will cause a failing seal to leak and high altitudes would be another aspect that could cause leaking to happen. When…
view full answer...I empathize with you because accidents do happen but if grease got on the brake shoes of your Hydraulic Trailer Brake Kit #AKUBRK-35-D to be safe you need to replace the shoes in order to ensure proper braking. For that you will need two of the…
view full answer...EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…
view full answer...