Replacement Landing Gear for 2010 Keystone Fuzion FZ322 Fifth Wheel Trailer

Question

Question:

I have a 2010 Keystone Fuzion FZ322 5th wheel toy hauler the existing front jack system has been snapping the bolts in the transfer bar that connects the 2 jacks, is there a replacement system that fits the existing setup

asked by: John H

0

Expert Reply:

There is a way for you to determine the correct replacement landing gear for your 2010 Keystone Fuzion, though we do not have landing gear made specifically for your trailer. Instead, you will need to measure the mounting brackets on your trailer from outside to outside like in the attached diagram and choose the amount of lift and weight capacity that will work for you.

For example, you may be able to use the Landing Gear # RVLG-8HDL, which has an 8,000 lb capacity, offers 20-1/2" of travel and includes a manual hand crank but can be upgraded to a motorized version with 12V DC motor # LC142178.

I've added a link to a page with our selection of landing gear for you to take a look at as well.

expert reply by: Kyle S

0

click to enlarge

Answer 1

If you are looking to replace your landing gear then I have a possible solution for you, we just don't carry any sets with the part VMC900R-304103 that you referenced. Our Landing Gear Set #RVLG-8HDL is rated for 8,000 lbs and has 20-1/2" of…

view full answer...

Answer 2

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Answer 3

We do carry the correct replacement for the worn out 1101422 / 214-1001 motor on your Kwikee electric steps, with the correct part being the following: - Replacement Motor for Kwikee Electric RV Steps #LC379147 These will work perfectly for you as a…

view full answer...

Answer 4

What you need for a replacement follow leg for your 2008 Keystone Fusion is the part #LG-179014. This is a fit to replace the VMC900L. The numbers after that aren't really important as the VMC900L is the part for the Venture landing gear.

view full answer...

Answer 5

The landing gear kit part #RVLG-8HDL will bolt right up in place of the landing gear you have installed currently on your 2003 Keystone Cougar 276EFS but the motor kit won't work since your old setup was a Fulton. What you'd need to add a…

view full answer...

Answer 6

Hi AJ, I can give you some help on selecting the right landing gear, though it is a universal type of fit, and there isn't landing gear specific to any trailer. That said, it's pretty easy to determine, as all you will need to do is measure…

view full answer...

Answer 7

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of…

view full answer...

Answer 8

If your brackets are 2" tall then you most likely have the standard weld stop measurements of 15-1/2" inside to inside (see attached photo). With this being the case I recommend going with the Landing Gear Set #RVLG-8000 which has a weight…

view full answer...

Answer 9

I've attached the wiring diagram for the Jensen RV Stereo - Double DIN - AUX/USB, Bluetooth, jControl - 12V #JWM60A (pictured below) which will show to the function of each wire color in the wiring harness to aid you during the installation…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Landing Gear for 2010 Keystone Fuzion FZ322 Fifth Wheel Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching