Adapter to Allow Hitch Ball with 3/4 inch Diameter Shank Fit 1 inch Ball Mount Platform Hole

Question

Question:

Can i use a 3/4 shank diameter ball with a one inch hole on ball mount

asked by: Bob

0

Expert Reply:

We have the sleeve adapter part # C21100 which is designed to fit a 1 inch ball mount hole diameter and allow a hitch ball with a 3/4 inch diameter shank fit it.

expert reply by: Jameson C

0

Answer 1

I recommend #20545I-EZ-60-10 Dexter Idler Trailer Axle w/ Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 60" Long - 2,200 lbs. I like this axle because of the EZ-Lube simple lubrication. You will also want to pick up a U-Bolt Kit #APUBR-10 for…

view full answer...

Answer 2

Yes, when installing the Draw-Tite Max-Frame Trailer Hitch Receiver #76020 on your 2018 Mazda CX-9 you will need to use a torque wrench to tighten down the hardware to the specifications listed in the installation instructions. This is the case with…

view full answer...

Answer 3

Hey Dave, thanks for reaching out! We don't have the 15" Lionshead Lynx Silver wheel, and that line has unfortunately been discontinued so we won't be able to get it either. If you just need one wheel like for a spare, then the Aluminum…

view full answer...

Answer 4

A couple things that can contribute to harmonic bouncing are improper tire type and improper tongue weight. You will want to be using LT tires as they have stiffer sidewalls which are better for towing than P rated tires. Also, be sure that your…

view full answer...

Answer 5

Hey Dale! Sorry to say but they stopped putting the brake controller adapter plugs in the Jeep Grand Cherokees a few years back. 2020 was the last model year they included them. The Curt Echo item #C51180 is going to be the only plug and play option.…

view full answer...

Answer 6

The correct replacement lift motor for a Maxxair Vent Fan 4751KS is the Replacement Lift Motor for Maxx Fan Plus Roof Vent part #MA10-20270.

view full answer...

Answer 7

While your Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2-1/2" Hitches - Matte Black #ERT00110 will physically fit the shank of the Shocker Hitch HD Ball Mount #SHK35VR, it will also interfere with the design of the shock absorber. As…

view full answer...

Answer 8

The Curt #C45456 has a length of 8-1/2" from center of hitch pin hole to center of ball hole. To allow you to us the Rock Tamers you have, I recommend the Gen-Y 2-Ball Mount for 2-1/2" Hitches #325-GH-064 which has a 9-1/2 inch center to…

view full answer...

Answer 9

I took a look at the Bargman Door Latch 10-30-051 that you referenced and it is indeed oversized. The best option we have to replace this would be the Global Link RV Entry Door Locking Latch Kit part #295-000019 which can install in an opening up to…

view full answer...

Answer 10

I would agree that it would be nice to have the ball mount hole diameter listed as a product category for the filters! I have a solution for your problem too! You would want the part #C21100 as this is a reducer that will allow your 3/4 inch shank…

view full answer...

Answer 11

An 1/8" of play is acceptable for the hitch ball. Especially with such a light weight hitch rating of the MaxxTow Adjustable-Height Ball Mount #MT70068 at 5,000lbs maximum. We do have bushings that can be used to allow balls to be used that are…

view full answer...

Answer 12

The height of the Curt Reducer Bushing for Ball Mounts, part #C21100 is .551 inches. This is the only size we have for this application.

view full answer...

Adapter to Allow Hitch Ball with 3/4 inch Diameter Shank Fit 1 inch Ball Mount Platform Hole

Product Page this Question was Asked From

Continue Researching