Trailer Hitch Receiver to Fit 2014 Jeep Grand Cherokee EcoDiesel

Question

Question:

Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2inch - 75699 I have a 2014 Jeep Grand Cherokee Ecodiesel. I would like to install the above listed hitch mount because I like the clean look. It says that it excludes diesel models. Can you confirm that this model would not fit on the diesel version? I dont like the way the tubing sticks out on the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 Item # C13182 .

asked by: Chris D

0

Expert Reply:

The Draw-Tite trailer hitch receiver part # 75699, does have a cleaner look than either of the two that fit the Diesel models; parts # C13182 and # 75713. However, the # 75699 doesn't fit the Diesel models because the DEF tank interferes with the location where the hitch installs. The two hitches that fit your 2014 Jeep Grand Cherokee show the crosstube under the bumper.

expert reply by: Charles S

0

Answer 1

You'll need a 20 amp circuit breaker for the brake controller power and a 40 amp circuit breaker for the battery charge line circuit from the trailer connector for a total of two. We actually offer a kit with these circuit breakers as well as the…

view full answer...

Answer 2

I spoke with my contact at Curt and he said if you have installed the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector #C55515, you will not need to do anything with the fuses to enable the trailer…

view full answer...

Answer 3

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 4

What type of brake controller do you have? Is it a proportional or time delayed? Also, are you using the brake pedal or the manual override? If you have a proportional brake controller and you are using the manual override then you should see a full…

view full answer...

Answer 5

As long as you have verified that the wire in question only goes hot when the brake pedal is applied, there is no reason why you cannot use the wire intended for the bed cap third brake light. If you do not have a circuit tester, we offer one, part…

view full answer...

Answer 6

I attached a diagram that shows how to match all of the wire colors of the Hopkins Multi-Tow 7-Way Blade and 4-Way Flat Trailer Connector #HM11141144 to the wire colors on your 2017 GMC Canyon.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Trailer Hitch Receiver to Fit 2014 Jeep Grand Cherokee EcoDiesel

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching