Can Extremely Tight Turn Cause Spring Bar to Come Loose on Weight Distribution System
Updated 04/18/2018 | Published 04/16/2018
Products Featured in This Question
Question:
How tight can you turn with the dual arm sway control before the end of the bar falls out of the sway arm? Can the vehicle be close to 90 degrees to the trailer? And is it the same for the round bar version? Thanks!
asked by: Randy J
Expert Reply:
It's possible that an extremely tight turn (like jack-knifing) can result in the spring bar sliding too far and coming off the dual-cam mount on the Reese Straight-Line Weight Distribution System # RP66084 that you referenced. This is really the case with any weight distribution system. Under normal driving conditions and turns, though, you should not have any issue at all with the arms falling out. When something like this happens, it is usually the result of reversing while making a sharp turn, which creates a jack-knife situation.
This particular system features a tongue weight capacity of 600 to 1,200 pounds. You will just want to make sure your total tongue weight, which is the loaded tongue weight of your trailer plus any added cargo weight coming from behind the rear axle of your tow vehicle, falls somewhere near the middle of this range. This is a really great system that will evenly distribute weight over the axles of your trailer and vehicle, while its self-centering sway control will keep your trailer in line.
You will just need to add a compatible hitch ball, such as the 2 inch # A-90 or the 2-5/16 inch # 19286.
I have attached a short video demonstration on this system, along with the written installation instructions that you can take a look at.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Suspension Enhancement
- Shop: Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle
- Search Results: tow mirrors
- Search Results: trailer dolly
- Shop: Parkit360 Force Electric Trailer Dolly - 2" and 2-5/16" Hitch Balls - 5,000 lbs
- Shop: Curt Welded Weight Distribution Shank 7" - 10 Hole Adjustment
- Shop: Curt Weight Distribution Shank - 14" Long - 7" or 7-1/2" Drop - 1,500 lbs TW
- Shop: Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Video: How to Choose a Trailer Brake Controller
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Should I Get Loadlifter 5000 Or 7500 For Towing A 15K Fifth Wheel
- Search Results: suspension enhancement
- Video: Choosing the Right Vehicle Suspension Upgrades
- Search Results: trailer jack
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Article: 5 Things to Know About Weight Distribution Hitches
on Weight Distribution Hitch
