Yakima SlimShady Clamps and Bracket

Question

Question:

Is it possible to purchase just the clamps for the slim shady awning? I want to mount a different brand awning that is larger than the slim shady to my Yakima corebars. Otherwise, is there another clamp that will work with an awning and my Yakima corebar rack?

asked by: Todd B

0

Expert Reply:

You'd want the SlimShady Mounting Bracket # 8880736 and Clamp # 8880737 for clamps of the SlimShady # Y36VR.

expert reply by: Jameson C

0

Answer 1

The only way to install a Yakima Skyline tower setup on a camper like what you have will require installing a set of tracks on the roof first like with the part #Y01135. If you have the clearance for the 60 inch long tracks, then the Yakima tracks…

view full answer...

Answer 2

Along with the Yakima fit kit part #Y01135 you'd also need four of the Skyline towers #8880614, the Yakima Corebar Crossbars #Y00423 and you'd be set. I attached a picture of the install instructions for you to check out as well.

view full answer...

Answer 3

Hi Mike; we have confirmation that the #8880736 will fit Roam awnings but it hasn't been tested on a 99 CVT Pioneer so I can't guarantee it will fit. There is no adapter unless you want to have one custom fabricated. I attached a diagram…

view full answer...

Answer 4

Since you have a roof rack with no T-Slots you won't be able to use the Tepui Overcast, but you can get a clamp on awning like the Yakima SlimShady #Y96VR! I've used these in the past and did the review on it as well! It works really well and…

view full answer...

Answer 5

Yes, we do carry both the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning #8880736, and the Replacement Clamp Assembly for Yakima SlimShady Roll-Out Awning #8880737 that you're inquiring about. These are both replacements for…

view full answer...

Answer 6

Hey Toby, You don't actually need the SlimShady brackets, you can use the Yakima MajorShady 270 Awning #Y72AV with the Yakima HD crossbars. It comes with the brackets and hardware needed to mount directly into the channels of the HD bars.

view full answer...

Answer 7

Yakima was unable to tell me the dimensions on the fabric for the Yakima MajorShady 270 Awning - Roof Rack Mount - Bolt On #Y72AV so I had one pulled from the warehouse and measured it myself. I've drawn up a little diagram below that shows…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Yakima SlimShady Clamps and Bracket

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching