Parts Needed to Install Yakima Corebar Roof Rack on Camper Shell

Question

Question:

Hi, I am looking to purchase and install roof racks to my truck cap. The truck is a toyota tacoma with the longer bed. I was looking at the 60: tracks: https://www.etrailer.com/Roof-Rack/Yakima/Y01135.html#exp-productdetails=.all-description. I just wanted to know what other equipment I need and if you have installation instructions.

asked by: Hal T

0

Expert Reply:

Along with the Yakima fit kit part # Y01135 you'd also need four of the Skyline towers # 8880614, the Yakima Corebar Crossbars # Y00423 and you'd be set.

I attached a picture of the install instructions for you to check out as well.

expert reply by: Jameson C

0

Instructions
(click to enlarge)

Answer 1

To add a set of tracks and crossbars for the roof of your ARE topper we have the Rhino Rack Aero Bar Roof Rack part numbers #Y02-480B which comes with everything needed to install and the tracks are 54 inches long.

view full answer...

Answer 2

The good news is that the roof rack manufacturers all decided to use the same channel dimensions so the roof rack accessories for roof channels basically all are interchangeable between (most) brands. Thule and Rhino Rack do work together just fine.…

view full answer...

Answer 3

For a replacement Yakima Skyline tower you would need the part #8880614.

view full answer...

Answer 4

The difference between the Yakima HD Crossbars like the #Y74MR and the regular Yakima Tracks like the #Y01135 is that they are compatible with different feet and adapters. With the HD tracks, they will fit the Yakima Skyline towers, OverHaul HD…

view full answer...

Answer 5

Hey Don, welcome back! You are always going to be limited by the lowest number when it comes to towing/tongue weight capacity. Even though the hitch is rated higher you're stuck with 500 lbs as the max. It is as you said, the tongue weight…

view full answer...

Answer 6

This is actually a common issue but it is easily resolved. If the change key comes out but the lock cylinder does not, the first step is to make sure the lock is unlocked. Then insert the change key. You may need to put tension on the key by pushing…

view full answer...

Answer 7

The only way to install a Yakima Skyline tower setup on a camper like what you have will require installing a set of tracks on the roof first like with the part #Y01135. If you have the clearance for the 60 inch long tracks, then the Yakima tracks…

view full answer...

Answer 8

You'd want the SlimShady Mounting Bracket #8880736 and Clamp #8880737 for clamps of the SlimShady #Y36VR.

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Parts Needed to Install Yakima Corebar Roof Rack on Camper Shell

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching