Adapter to Connect a Round 7-Way Trailer Connector on a Semi to a Gooseneck Trailer with a 7-Blade

Question

Question:

I have an International Semi with a 7 pole round that I want to tow a gooseneck trailer with a RV style hookup. What adapter could I use to get the lights to work properly? Thanks

asked by: Ben V

0

Expert Reply:

Use Hopkins part # HM47425. It's an adapter that plugs in to your round 7-way and gives you a 7-blade RV style connector.

expert reply by: Charles S

0

Answer 1

Hello Dustin, To mount the TecNiq Mini Side Marker Light - Amber - 3/4" - Grommet Mount - 9" Wire #TN22XR, you’ll need to drill a 3/4-inch diameter hole. The rubber grommet is designed to press-fit into this standard hole size, allowing the…

view full answer...

Answer 2

Both the LED Trailer Mini Clearance #MCL10AKB and Uni-Lite LED Clearance #MCL11RKB will require an 11/16" hole for mounting. These both use the same Grommet #A11GB.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Adapter to Connect a Round 7-Way Trailer Connector on a Semi to a Gooseneck Trailer with a 7-Blade

Featured Help Information

Miscellaneous Media

Continue Researching