Single Motorcycle Ramp Recommendation for Motorcycle

Question

Question:

One of these is exactly what im looking for for my bike.

asked by: Dean

0

Expert Reply:

We have a ramp similar to the # 288-07501 sold individually that's actually intended for a bike. Check out the Arched Loading Ramp # 288-07452. The arches of the ramp make loading the bike a bit easier than a ramp that is totally straight. This ramp is 90 inches long.

For a shorter 48 inch ramp we have the part # 288-07474 instead that is 11 inches wide.

expert reply by: Jameson C

0

Answer 1

In my experiance Bob, I find the Tekonsha #118726 is more durable over the Curt #C56315 for your 2016 Chevrolet Volt. Tekonsha wiring tends to have less issues with the converter portion going out down the road.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Single Motorcycle Ramp Recommendation for Motorcycle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching