See what our Experts say about this Stallion ATV Ramps

• Are Stallion Aluminum Car Hauler Ramps Available Individually
  The # 288-07501 is only available as a set from Stallion with no options for the individual ramps. Depending on your needs, they do have another 48" ramp available individually which is the # 288-07474. This ramp is 48" long x 11" wide and has a weight capacity of 800 lbs.
  view full answer...
• What is the Weight Capacity of the Stallion ATV Ramp # 288-07474?
  I have a solution for you. As far as the load rating of the single Stallion Loading Ramp - Steel - 48" Long x 11" Wide # 288-07474, it has a weight capacity of 800 pounds. However, when you use the ramp as a pair like the 2 that come with the # 288-07474-2, the weight capacity becomes 1,600 pounds when combined. As far as whether we have a 60-inch Stallion ramp, the only ones we carry are the Aluminum Car Hauler Ramp Set - 60" x 14-1/2" - 6,000 lbs # 288-07502 (which only come in quantities...
  view full answer...
• Option for Carrying 420 lb Wheel Chair with 2011 Honda Odyssey
  I have an outside of the box solution for allowing you to transport your wheelchair but your 2011 Honda Odyssey does not have the weight capacity to carry 420 lbs at the rear of it like you have found out the hard way. We came up with an interesting idea that should work but it will require you to remove your captain seats in the second row of van. What you could then do is use ramps like part # 288-07474 to drive the chair in and then it could be transported there. Otherwise your other...
  view full answer...
• Single Motorcycle Ramp Recommendation for Motorcycle
  We have a ramp similar to the # 288-07501 sold individually that's actually intended for a bike. Check out the Arched Loading Ramp # 288-07452. The arches of the ramp make loading the bike a bit easier than a ramp that is totally straight. This ramp is 90 inches long. For a shorter 48 inch ramp we have the part # 288-07474 instead that is 11 inches wide.
  view full answer...
• How to Transport 65 Pound Scooter on 2008 Hyundai Elantra
  You are correct that there are only Class I trailer hitches available for your 2008 Hyundai Elantra. There are adapters available that can convert the 1-1/4 inch receiver opening on a Class I hitch to a 2 inch opening but it will reduce its capacity by 50 percent so this won't be a good option with a heavier scooter. The best option we have to transport your scooter will be with a lightweight cargo carrier that is compatible with Class I hitches and is large enough for your scooter....
  view full answer...
• Where Is the Length of the Stallion Loading Ramps Measured
  In regards to loading ramps like the Loading Ramp part # 288-07474, the length includes the lip/tabs on the top or bottom.
  view full answer...
• Cargo Carrier Recommendation for 120 lb Motorcycle with Class II Hitch
  This would depend on the dimensions of your motorcycle. The biggest carrier would be the 19 inch by 47 inch Curt cargo carrier part # C18110 which fits Class II hitches like what you have and has a 300 lb capacity. The total weight of the carrier is 30 lbs which gives you 320 lbs of capacity left over for the weight of your motorcycle. This does not have a ramp that comes with nor is one made specifically for it. So if you're okay with lifting the bike, and it would fit, you could lift...
  view full answer...
  
• Does Curt Cargo Carrier Work With Class I Trailer Hitch for 2017 Mazda CX-3
  I'm happy to confirm for you that the products you mentioned are each compatible for use on your 2017 Mazda CX-3, and the Curt Cargo Carrier is compatible with a Class I hitch, so what you will need are the following: - Draw-Tite Trailer Hitch Receiver # 24933 - Curt Cargo Carrier # C18110 - Loading Ramp # 288-07474 The ground clearance is about 11-1/2 inches from the top of the receiver on your Mazda to the ground, so you will want to go over any very sudden, steep inclines (like a...
  view full answer...

Do you have a question about this ATV Ramp?