Replacement Release Clip Recommendation for Fastway e2 Weight Distribution Round Bars

Question

Question:

I have the round swaybars and where they go into my hitch. One of the clips that secures the bar has fallen out and lost. Are these replaceable on the ball hitch.

asked by: Billy S

1

Helpful Expert Reply:

Sounds like you have a Fastway E2 weight distribution system and need new release clips to replace lost ones. For that you'd want the part # FA94-02-1059.

expert reply by: Jameson C

1

Answer 1

Reese does not offer the spring bar retainer clips like you have referenced. The really good news is that you can use either the Replacement Spring-Bar Release Clip #FA94-02-1059 or Curt #17109. These clips will work as replacements for the hitch you…

view full answer...

Answer 2

Hey John! It sounds like you lost one of the spring bar clips on your Fastway e2. What you need is the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059. If you need anything else feel free…

view full answer...

Answer 3

First you have to get the lower screw out of the head of the system. Since the screws don't have a slot or Philips head on them you'll have to pry them out some have to use a chisel. Once they are out you'll slide the clip down so that it…

view full answer...

Answer 4

We currently have the Spring Bar Retainers from Curt #17109 and Fastway #FA94-02-1059.

view full answer...

Answer 5

Since we do not carry the Haul-Master line of weight distribution hitches, we do not have access to their replacement parts. I also do not have a way of saying for sure if the Curt Spring Bar Retainer Package #17109 would work with your Haul-Master…

view full answer...

Answer 6

We have a few different clip options that are possible fits for your Weight Distribution (WD) system. Fastway WD - FA94-02-1059 Curt WD - 17109 From the picture that you sent me, I believe that the Curt clips #17109 are the correct replacement clips…

view full answer...

Answer 7

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry out…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

There is a wiring kit for a brake controller Preston but it's not going to be a plug and play one. The 2025 Toyota Tacoma does not have a plug in brake controller port. Toyota stopped putting them in after the 2023 model. For your Tacoma, I…

view full answer...

Answer 12

I have a solution for you because as you know what you have now cannot charge Lithium batteries. You will need the Progressive Dynamics #PD4135K which is designed to replace your WF-8735P and is compatible with Lithium batteries. When this is…

view full answer...

Replacement Release Clip Recommendation for Fastway e2 Weight Distribution Round Bars

Product Page this Question was Asked From

Continue Researching