Removing and Reinstalling New Retainer Pins in Fastway Weight Distribution System

Question

Question:

how to replace round bar release clip

asked by: Dorsey K

1

Helpful Expert Reply:

First you have to get the lower screw out of the head of the system. Since the screws don't have a slot or Philips head on them you'll have to pry them out some have to use a chisel. Once they are out you'll slide the clip down so that it will pass through the hole in it. You'll then have to pry out the top pin as well. To install new one you'd reverse the process.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Reese does not offer the spring bar retainer clips like you have referenced. The really good news is that you can use either the Replacement Spring-Bar Release Clip #FA94-02-1059 or Curt #17109. These clips will work as replacements for the hitch you…

view full answer...

Answer 2

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry out…

view full answer...

Answer 3

As far as I know this is not a common problem, and not something that we have had reported as an issue for the #FA94-00-1000. It is important to make sure that everything is secure when installing the weight distribution hitch. The spring bars should…

view full answer...

Answer 4

We have a few different clip options that are possible fits for your Weight Distribution (WD) system. Fastway WD - FA94-02-1059 Curt WD - 17109 From the picture that you sent me, I believe that the Curt clips #17109 are the correct replacement clips…

view full answer...

Answer 5

Since we do not carry the Haul-Master line of weight distribution hitches, we do not have access to their replacement parts. I also do not have a way of saying for sure if the Curt Spring Bar Retainer Package #17109 would work with your Haul-Master…

view full answer...

Answer 6

Sounds like you have a Fastway E2 weight distribution system and need new release clips to replace lost ones. For that you'd want the part #FA94-02-1059.

view full answer...

Answer 7

Hey John! It sounds like you lost one of the spring bar clips on your Fastway e2. What you need is the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059. If you need anything else feel free…

view full answer...

Answer 8

We currently have the Spring Bar Retainers from Curt #17109 and Fastway #FA94-02-1059.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Removing and Reinstalling New Retainer Pins in Fastway Weight Distribution System

Product Page this Question was Asked From

Continue Researching