Replacement Clips for Weight Distribution System

Question

Question:

I am looking for the replacement clips that are part of the stabilizer system on my trailer hitch. These are the clips that hold the actual stabilizer bars in place on the vehicle. I have had to replace them before about every year so I know they exist, but I can not find them on your site. I purchased my stabilizer bar from etrailer about 4 years ago. Thank you in advance for your assistance.

asked by: Emma

0

Expert Reply:

We have a few different clip options that are possible fits for your Weight Distribution (WD) system.

Fastway WD - FA94-02-1059
Curt WD - 17109

From the picture that you sent me, I believe that the Curt clips # 17109 are the correct replacement clips for you.

expert reply by: Jon G

0

Answer 1

We currently have the Spring Bar Retainers from Curt #17109 and Fastway #FA94-02-1059.

view full answer...

Answer 2

Hey John! It sounds like you lost one of the spring bar clips on your Fastway e2. What you need is the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059. If you need anything else feel free…

view full answer...

Answer 3

Reese does not offer the spring bar retainer clips like you have referenced. The really good news is that you can use either the Replacement Spring-Bar Release Clip #FA94-02-1059 or Curt #17109. These clips will work as replacements for the hitch you…

view full answer...

Answer 4

First you have to get the lower screw out of the head of the system. Since the screws don't have a slot or Philips head on them you'll have to pry them out some have to use a chisel. Once they are out you'll slide the clip down so that it…

view full answer...

Answer 5

Sounds like you have a Fastway E2 weight distribution system and need new release clips to replace lost ones. For that you'd want the part #FA94-02-1059.

view full answer...

Answer 6

Since we do not carry the Haul-Master line of weight distribution hitches, we do not have access to their replacement parts. I also do not have a way of saying for sure if the Curt Spring Bar Retainer Package #17109 would work with your Haul-Master…

view full answer...

Answer 7

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry out…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

There is a wiring kit for a brake controller Preston but it's not going to be a plug and play one. The 2025 Toyota Tacoma does not have a plug in brake controller port. Toyota stopped putting them in after the 2023 model. For your Tacoma, I…

view full answer...

Answer 11

Hey Todd! Yes, the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack w/ Tonneau Cover Adapters #Y01151-5755 is compatible with the Synetic MR Retractable PRO Tonneau Cover on your 2025 Toyota Tacoma. The adapters will fit the T-slot rails on that…

view full answer...

Answer 12

Hello Hal, Great question! It really would be nice if Toyota kept their receiver the same size as everyone else’s so any standard 2" lock would fit. The good news is that Infinite Rule actually made a lock specifically for the 2024+ Toyota…

view full answer...

Replacement Clips for Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching