Replacement Drop Leg for Ram 2,500 lb Square Direct Weld Jack

Question

Question:

i have Ram 2500 lb jack will the the 3000lb leg fit my jack

asked by: Rocco S

0

Expert Reply:

The Replacement Drop Leg # TJD-5000-FT is designed to be used with Ram TJD-5000 Series jacks so if that's what you have it will work for you. You can also compare the dimensions of this leg with your current one to see if they are equal. This replacement drop leg has a tube width of 1-3/4", a footplate that is 7-1/2" long x 3-3/4" wide and a 5/8" pin hole diameter. You can use the accompanying photo as a reference and I've also linked a video review of this part for you to take a look at.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Hey Dakota, the Fulton Square Drop Leg for Stabilizer Jack #FSJ40324 that you referenced is rated individually at 3,000 lbs. So if you were using two it would have a capacity of 6k but you would also need the outer tube part #FSJ10300 as well to…

view full answer...

Answer 2

If your 2010 Chevy Express has tow package wiring already run under the dash, the wires should be labeled with a white tag that holds them together that tells you what each wire does. If, not, you will need to use a circuit tester, #PTW2993, to test…

view full answer...

Answer 3

I may have a solution for you, however we do not have a trailer jack available that features an outer tube diameter of 1-7/8 inches. The best recommendation I have is to simply install a new bottom support plate like the Bulldog Jack Support Plate…

view full answer...

Answer 4

None of the jacks we offer have tube dimensions that would be small enough to fit the bottom support plate on your trailer that is 1-7/8 inches in diameter. The best recommendation I could make would be to install a new bottom support plate like part…

view full answer...

Answer 5

Yes, drop leg #TJD-5000-FT will fit trailer jack #MJSQ-2500B. The drop leg that comes with this jack is 1-3/4 inches square which is the same as #TJD-5000-FT. And it has the same hole spacing.

view full answer...

Answer 6

The square tubing on the Replacement Drop Leg #TJD-5000-FT is 3/32" thick.

view full answer...

Answer 7

Hello Jeff, I am always looking for an opportunity to go stretch my legs, so I appreciate you needing this measurement. The inside measurement of the Replacement Drop Leg for etrailer and Ram Square Direct Weld Jacks #TJD-5000-FT is right at 1…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Drop Leg for Ram 2,500 lb Square Direct Weld Jack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching