Recommended Torque Wrench for Trailer Hitch Installation

Question

Question:

For those of us that do not have a torque wrench what would be your recommendation?

asked by: Todd

0

Expert Reply:

For the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" # C12172, there really isn't a solution other than to use a torque wrench. Without torqing the necessary bolts to the manufacturer specs, you void the warranty and can have safety issues when using the hitch receiver.

If you want to purchase one, I recommend the torque wrench # ALL944001 or the digital adapter # ALL940962. There are many auto parts stores that now rent tools as well if you prefer to go that route, but it is nice to have one for situations like this.

expert reply by: Jason S

0

John G.

5/16/2020

I bought a hitch from you that says it has to be torqued to 380lbs ft. The above-recommended torque wrench only goes to 250 lbs. Can you recommend one that can handle 400 lbs ft? Thanks

Reply

Chris R.

5/20/2020

We don't have any torque wrenches available that go that high. Your best bet will be a local hardware or auto parts store. Like Jason mentioned above, you should be able to even borrow one from the latter.

Reply

John G.

5/20/2020

@ChrisR Forgive me Chris, I meant to confirm what the amount of torque is for the bolts. The paper that came with it says the 3/4 hardware should be torqued to 380lbs ft. The online instructions say 320 lbs ft, and everyone i've talked to that are mechanics say over 300 is too much. Can you confirm what the proper amount of torque is for the 13333 hitch is? Thanks

Reply

Chris R.

5/22/2020

@JohnG I gotcha! On the Curt Trailer Hitch # 13333 all 3/4" hardware should indeed be torqued down to 320 lb-ft. Curt does tend to recommend higher torque values than normal, but you can be assured that it won't cause any damage to the bolt or hitch.

Reply

Answer 1

Hey Chuck! The Curt Trailer Hitch Receiver #C66KR may limit the functionality of the hands-free sensor on your 2025 Toyota RAV4 Hybrid. The liftgate itself will still work as intended. This is typically unavoidable on vehicles with the hands-free…

view full answer...

Answer 2

Hey Julie, to install the Curt hitch part #C77MJ you do need to lower the exhaust of your 2022 Toyota RAV4. This is a very standard step for hitch installs that it's almost required. As someone who has done it a few times it's also not that…

view full answer...

Answer 3

Hi Stephanie! Great question and you’re totally right to ask, because most hitches for the 2024 RAV4 do require a bit of bumper trimming. That includes the Oris Detachable Hitch #TS66VR, since it uses a hidden design that needs a hole cut in the…

view full answer...

Answer 4

I have confirmed with Draw-Tite that #75956 is actually not a fit for your vehicle. The Curt Trailer Hitch Receiver Class II 1-1/4" #C12172 that you mentioned is a confirmed fit for your vehicle, however, I recommend going with the Curt Trailer…

view full answer...

Answer 5

The trailer hitch I strongly recommend for your 2020 Lexus NX 300 is the Curt Trailer Hitch Receiver #C13337 because it is a complete and simple bolt-on install that does not require any drilling into your vehicle's frame to install, and because…

view full answer...

Answer 6

Hey Alan, yes the Thule ReVert bike rack part #TH83VA can be used in your Honda Odyssey 2 inch hitch. In the picture I attached you can see that the bikes back wheel is held higher than the shank of the rack so ground clearance should be good but it…

view full answer...

Answer 7

We can get you a great cargo carrier for your 2017 Tesla Model X that is lightweight so your pup has enough room to enjoy the ride with you; that's a pretty big dog so they need all the room they can get! What I highly recommend is the Curt Cargo…

view full answer...

Answer 8

The Curt Cargo Carrier #C18113 will definitely work with the etrailer #e25TR on your 2024 Outback. Keep in mind, you will be limited to the 350 lb max tongue weight of the hitch or the max tongue weight of your vehicle. Whichever is lower is what you…

view full answer...

Answer 9

The main difference between these three hitches is going to be the looks and install time. EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - Class III - 2" #306-X7391. Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13409.…

view full answer...

Answer 10

The install hardware that is included with the Curt Hitch part #13322 that you referenced includes bolts that are M14-2.00. That size of bolt head calls for a 21 millimeter socket or wrench. I attached an install video for you to check out as well.

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

To help alleviate the back and forth chucking you are experiencing with your 2 inch receiver there are a couple of things I recommend doing. First is to use a cushioned ball mount, the Convert-A-Ball, which is designed to reduce this type of movement…

view full answer...