Bolt Hole Measurements of the Curt Trailer Hitch Receiver Class III 2" # 13408

Question

Question:

I would like to purchase the above parts iv tried online but you do not accept payment from united kingdom.

asked by: James F

1

Helpful Expert Reply:

My contact at Curt Manufacturing confirmed, that the bolt holes on the Curt Trailer Hitch Receiver Class III - 2" # 13408, are spaced 4.35" on center from front to back. The forward most holes are spaced 39.937" apart on center, and the rear most holes are 39.437" apart on center.

expert reply by: Timothy G

1

James F.

2/7/2018

I would like to purchase the above parts iv tried online but you do not accept payment from united kingdom.

Timothy G.

2/15/2018

You may use PayPal to place the order and just have it delivered in U.S.

Answer 1

Hey Carl, we have checked with Curt and they have told us that the Curt Bullseye part #RVI64FR can work with the RVI Brake 3 as long as the serial number is above 35,000. Is that what they told you as well or did they mention the serial number at…

view full answer...

Answer 2

The RVi4 Portable Supplemental Braking System from Curt #RVI44FR uses an onboard accelerometer to detect changes in inertia, so when your motorhome slows down, the RVi4 senses it and applies the toad’s brakes proportionally. It even adjusts for…

view full answer...

Answer 3

Thank you for the photo! What you have there is a deep drop or "cowboy" bumper. So, for a 2 inch trailer hitch that is confirmed to fit your 1989 Ford F-250 XLT Lariat with the deep drop bumper, I recommend the Curt #C15511. This 3-piece…

view full answer...

Answer 4

To verify exactly where the end of the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 will sit in relation to your CM flatbed you will need to measure from the mounting holes. The rearmost mounting hole which will sit just behind the rivet in…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver #C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes.

view full answer...

Answer 6

The drop of the B & W Class V #BWHDRH25198 is 7-3/8 inches. That represents the distance from the underside of the frame member where the hitch mounts to the top of the receiver tube. If that isn't sufficient to clear your bumper, the Curt…

view full answer...

Answer 7

I would be happy to help. The Curt Trailer Hitch Receiver #C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes. The Curt…

view full answer...

Answer 8

The mounting holes are going to be slightly different for the Curt Trailer Hitch Receiver #C15300 that fits a standard or step bumper on a 1996 Ford F-250 or F-350 compared to the Curt 3-Piece Trailer Hitch Receiver #C15511 that fits the same truck…

view full answer...

Answer 9

The Curt 3-Piece Trailer Hitch Receiver #C15511 that you referenced is a great option for the deep drop bumper on your 1997 Ford F-350 Heavy Duty. The Draw-Tite #41504 is a little more cost-effective but it also requires the use of the adapter kit…

view full answer...

Answer 10

The B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" #BWHDRH25198. This is a heavy duty hitch that measures 7-3/8 inches from the frame to the top of the receiver. As long has his deep drop bumper fits with the 7-3/8 inch…

view full answer...

Answer 11

When measuring the frame width on a vehicle, you will need to measure from the outside of one frame rail to the outside of the other frame rail. It sounds like you have the 37-1/4 inch frame on your 1983 Ford F-100. The Curt Class IV 2 Inch Hitch,…

view full answer...

Answer 12

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...