Can the Lippert Scissor Stabilizer Jacks # LC285326 be Installed on a 26 foot Motorhome

Question

Question:

Could these be installed on a E450 26ft motor home?

asked by: Dale

1

Helpful Expert Reply:

The Lippert Scissor Stabilizer Jacks # LC285326 that you referenced can definitely be used on a 26 foot motorhome that is on a Ford E-450 chassis.

These are a universal fit so you will just need to make sure that you have enough space on your frame to mount the 10-1/4" long x 3-1/4" wide base. I have attached a photo giving some dimensions for you.

These jacks have a load capacity of 10,000 lbs (5,000 lbs each) and can give you up to a 24" lift. Any set of scissor jacks are meant to help stabilize some of the weight of your RV or trailer, so you never want to use these to actually lift your RV or trailer.

I have also attached a review video for you to check out.

expert reply by: Jon G

1

click to enlarge

Answer 1

Hi LeRoy! I went out to the warehouse and measured this directly for you, and the center to center distance between the two holes on the dogbone base is 6-1/2 inches. That measurement is consistent across our etrailer scissor jack variations,…

view full answer...

Answer 2

Hey David, thanks for the picture! I went down to the warehouse and measured the mounting bolt pattern on the etrailer Scissor Stabilizer Jack item #e36VV and their identical to the ones in your diagram. This jack is going to be a perfect replacement…

view full answer...

Answer 3

Hey Allen, thanks for reaching out. For bolting on the etrailer Scissor Stabilizer Jacks #e36VV the recommended hardware is self-tapping 3/8" x 1" screws. If you use that, you won't need any bolts or washers or anything. You'll want…

view full answer...

Answer 4

I am attaching a photo of the mounting locations on the Ram Scissor Stabilizer Jack #TJSC-24 that I believe you were referencing. They are from the edges of the mounting holes but I believe your mounting hole locations would match up just fine. Let…

view full answer...

Answer 5

The Scissor Stabilizer Jack #TJSC-24, which also comes in a 2-pack #TJSCHD-24 and a 4-pack #TJSCHD-24-4, is a universal fit so you would need to double check our measurements to ensure they fit your travel trailer. When they are collapsed they…

view full answer...

Answer 6

The spacing for the Lippert Scissor Stabilizer Jacks with Handle #LC285344 that you have pictured is approximately 1-7/8".

view full answer...

Answer 7

I apologize for the confusion, but what's going with the Ram Scissor Stabilizer Jack #TJSC-24 is that it will move a total of 18-3/4 inches which gives it an overall height of 23-3/4 inches. So while the two numbers are confusing they are both…

view full answer...

Answer 8

If you are needing to replace the stabilizer jacks on your 2011 K-Z Durango 1500, we will have 2 different styles. The Stallion Stabilizer Jacks #288-01892-2 are a drop down style so they are easy to use, but they are only rated up to 1,000 pounds…

view full answer...

Answer 9

For some unknown reason stabilizer manufacturers love to just make each stabilizer's mounting holes slightly different than the rest. While we don't have an exact match to the dimensions you stated you luckily can still use almost any other…

view full answer...

Answer 10

Hey Edgar, I've attached a diagram below that should have all the measurements you need for the mounting brackets of the etrailer Scissor Stabilizer Jacks w/ Handle #TJSCHD-24-4. The brackets are about an 1/8" thick.

view full answer...

Answer 11

The R-Pod 189 usually comes fitted with four corner-mounted scissor jacks that bolt to the frame. We have a number of such bolt-on stabilizer jacks that are shown on the linked page. Many of these are sold as pairs but we also have single jacks too,…

view full answer...

Answer 12

The stabilizer jacks aren't trailer specific, but the mounting hole spacing is pretty standard across the board. I'd recommend removing the damaged jack and comparing the mounting plate hole spacing to what's shown in the provided photos.…

view full answer...

Can the Lippert Scissor Stabilizer Jacks # LC285326 be Installed on a 26 foot Motorhome

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching