Will Lippert Scissor Jack # LC285325 Fit Tristar 5000

Question

Question:

Is this the correct replacement for Tristar 5000?

asked by: Mike W

1

Helpful Expert Reply:

Yes, since RV scissor jacks like the Lippert # LC285325 are all universally designed this would fit your Tristar 5000.

expert reply by: Jameson C

1

Bolt Pattern of Stabilizer Jack
(click to enlarge)

David

9/24/2024

Hi Jameson, So if the Lippert LC285325 will fit the same as the Tristar 5000, will the Lippert LC285326 also fit the same as the tristar 5000? Thank you!

Jameson C.

9/24/2024

@David It will fit but I am not able to verify for sure if it's an exact fit or not.

David

9/24/2024

@JamesonC I really don’t have much confidence in your answer. You were able to answer someone else’s question about a very similar product ! I thought you guys were the professionals who could answer these type questions??

Jameson C.

9/24/2024

@David It sounded like you were asking if it was an exact direct fit which we don't know. I can state that it will work great as a replacement but the bolt pattern could possibly be different and you might have to make some modifications. Hopefully that makes more sense.

See All (5) Replies to David ∨

Answer 1

Hey Ben! The bracket on the etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter #e96VV is a pretty standard one and can be bolted on or welded. I'm attaching a photo of the bolt hole dimensions in relation to each other so you can…

view full answer...

Answer 2

Yes, we do carry water pumps that can be used to replace your Shurflo 4008-101-A65 water pump. After looking at the specifications of the Shurflo 4008-101-A65, I recommend replacing it with the HydroMax RV Fresh Water Pump #P25201. The HydroMax RV…

view full answer...

Answer 3

Hi LeRoy! I went out to the warehouse and measured this directly for you, and the center to center distance between the two holes on the dogbone base is 6-1/2 inches. That measurement is consistent across our etrailer scissor jack variations,…

view full answer...

Answer 4

Hey Allen, thanks for reaching out. For bolting on the etrailer Scissor Stabilizer Jacks #e36VV the recommended hardware is self-tapping 3/8" x 1" screws. If you use that, you won't need any bolts or washers or anything. You'll want…

view full answer...

Answer 5

Hi Peter! The Soft Start Kit for Coleman-Mach RV Air Conditioners #CM56RR is what you need. This is designed to fit Coleman-Mach Series 45000, 47000, and 48000 AC units. The 48204-669 you have falls under the 48000 so they are compatible. Where are…

view full answer...

Answer 6

Hey Brian, we do not have a thermostat control setup for your roof vent. If that's something you needed you'd have to go with a different vent assembly like the MaxxFan part #MA00-04002K.

view full answer...

Answer 7

Hey Ray, thanks for reaching out. If you are set on placing the propane tank inside the toolbox, it can be done safely as long as the box is properly vented at the bottom. Propane is heavier than air, so if there is ever a small leak it will settle…

view full answer...

Answer 8

There are no replacement parts for the trailer scissor jacks, if they are damaged such as the rod being bent then you will simply need to replace the jack for which we have the Lippert Scissor Stabilizer Jack part #LC285325 or part #LC285326 for the…

view full answer...

Answer 9

The Replacement Base for B&W Companion 5th Wheel Trailer Hitch - 20,000 lbs #BWRVB3500 will fit any turnoverball gooseneck hitch. The new head #BWRVC3006 basically gives you the B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter…

view full answer...

Answer 10

The globrite 122 in red or yellow/amber are 3.75 inches by 1.70 inches from what I can find online. We do not have a direct replacement, however the closest dimension we have to replace them is 3-1/2 by 1 inch. I recommend the #MC68RB and #MC68AB. If…

view full answer...

Will Lippert Scissor Jack # LC285325 Fit Tristar 5000

Product Page this Question was Asked From

Continue Researching