Thule Replacement Wheel Cradle For Older Thule T2 Bike Rack

Question

Question:

The dimensions of the remaining wheel cradle on my Thule T2 Bike Rack are: bolt holes 5and1/2inch on center, 2inch width and 8inch long which dont match that of Part Number 853-5958. Do you have something which will fit? The number 515-5190 is on the rack and I believe I bought it sometime prior to 2012. Thanks!

asked by: Kyle M

0

Expert Reply:

So I checked with Thule and for the version of the T2 that would have been bought prior to 2012 the correct wheel tray is the part # 853-5958 that you referenced.

expert reply by: Jameson C

0

Answer 1

The Thule Replacement Front Wheel Cradle for Thule T2 Bike Racks #853-5958 will work on the SportWorks rack you pictured as long as the measurements are consistent. The cradle has a base that is 9-1/4 inches long and 3 inches wide with bolt holes…

view full answer...

Answer 2

We do have replacement hardware for the Thule T2 Classic 2 Bike Rack TH9044. The specific bolt that holds the tire tray in place is the Replacement Slotted Cutting Bolt for Thule T2 Classic Bike Platform Rack #TH34FR. This bike rack uses 2 of these…

view full answer...

Answer 3

Thanks for getting me the pictures of your Thule T2! From that I can tell you have the T2 Classic like #TH9044 and the correct wheel holder would be the part #7521568001. This would also work on the #TH9044-TH9046.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Thule Replacement Wheel Cradle For Older Thule T2 Bike Rack

Product Page this Question was Asked From

Continue Researching