Dimension of Safety Step # SASA-10C-G Base Legs at Full Height

Question

Question:

How long and how wide is this step at the bottom of the legs at 9 ins?

asked by: Jack R

1

Helpful Expert Reply:

At the full 9 inch height, the Safety Step 19 x 15 Inch # SASA-10C-G is 24 x 19 inches. I've attached a photo and a couple videos to assist.

expert reply by: Jason S

1

click to enlarge

Answer 1

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hello Adam, we meet again! I have two options for a lock that fits your Gen-Y Hitch Gooseneck Pin Box #GY38FR. The first is the InfiniteRule Lock for Gen-Y Hitch SnapLatches #IR48FR. This runs through that hole on the back of the latch to secure it,…

view full answer...

Answer 8

Good question, Steven. Thanks for asking! Yes, you'll need the Furrion 7-Way Vehicle Power Adapter #FR87PR for your Haloview cameras to function properly. The adapter provides constant 12 volt power, bypassing the truck's pulse-width…

view full answer...

Answer 9

Hey Garret, I would definitely go with what Equal-I-zer recommended with the part #EQ37120ET which would be the correct rated system for your 2019 Heritage Glen 282RK. You are correct in that if you go with a system that is rated too high you will…

view full answer...

Answer 10

Hey Quinn. The installation time for the Hellwig Adjustable Big Wig Rear Anti-Sway Bar item #HE96XR ranges from 1-1/2 to 3 hours depending on experience and access to a lift. Plus it depends on whether or not you have to remove a factory sway bar and…

view full answer...

Answer 11

Hey Mike! The Soft Start Kit for Coleman-Mach RV Air Conditioners #CM56RR is designed to work with 45000, 47000, and 48000 air conditioners. Based on those numbers I'm assuming you those are 38000 series, but the model number doesn't always…

view full answer...

Answer 12

Hey Orv, thanks for reaching out. Yes, that Bargman 50-97-410 harness has been discontinued but we do have a suitable replacement for it. Take a look at the following: - Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector for Aluminum…

view full answer...

Dimension of Safety Step # SASA-10C-G Base Legs at Full Height

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching