Does the Ventline Wall Vent Need to be Caulked?

Question

Question:

Does the wall vent need to be caulked?

asked by: Michael

0

Expert Reply:

The Ventline Exterior Wall Vent for RV Range Hood # V2111-13 does require TremPro 644 Silicone Sealant # 0160297 in order to be installed.

expert reply by: Kyle S

0

Answer 1

The RhinoFLEX RV Sewer Hose Extension with Swivel Lug and Bayonet Fittings #CAM39765 and similar items do have removable orange fittings but there are not replacement parts available. If you have the fittings then you just need the hose #CAM39671. If…

view full answer...

Answer 2

The two orange fittings at the ends of the RhinoFLEX RV Sewer Hose, part #CAM39761, are designed to come of easily. The ends can be removed by twisting the black locking rings until loose. From there, you can unscrew the orange fittings. This makes…

view full answer...

Answer 3

The Valterra RV Sewer Hose Carrier #A04-5094BK has a 4-1/2" inner diameter and the Camco RhinoFLEX RV Sewer Hose w Swivel Fittings #CAM39761 is approximately 3" in diameter so you'll be able to fit all of it except for the 90 degree…

view full answer...

Answer 4

The Camco RhinoFLEX Sewer Hose part #CAM39761 that you referenced uses standard RV sewer connections like what Valterra would have. On the RV side (the side that would attach to a Valterra fitting) there is a bayonet fitting which is an industry…

view full answer...

Answer 5

The d-shaped shaft of the Ventline motors is an older style no longer made. You might be able to replace the fan blade you have now as well but I'd need to know diameter of the blades you have.

view full answer...

Answer 6

Hi Norm; the B&W Digital Tongue Weight Scale #BW34KR is designed for bumper pull trailers only. The coupler will fit onto the scale to measure tongue weight. There is no way to safely hook up a 5th wheel or gooseneck to the scale and measure. The…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Does the Ventline Wall Vent Need to be Caulked?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching