How Does Washer Face when Installing Curt Hitch # C13146

Question

Question:

The washer has a curve to it. Should I put the convex or concaved part of the washer against the nut head?

asked by: David

0

Expert Reply:

You'd want to put the convex side of the washer against the bolt head of the hardware that comes with the Curt hitch # C13146 when installing it. That way the head pushes it flat as you tighten it which acts as a lock nut.

expert reply by: Jameson C

0

Answer 1

Hey Chris, the CURT Class 3 Trailer Hitch #C37RV won't require any bumper modification, but the etrailer Class 3 Trailer Hitch will require some underbody panels/fascia to be trimmed for install.

view full answer...

Answer 2

Hi Chris, Yes, you'll need the Curt Trailer Hitch Receiver #C37RV. This class III trailer hitch has a 4,000lb maximum towing capacity and 600lb tongue weight capacity, but you'll still want to refer to your Santa Fe's owner manual to…

view full answer...

Answer 3

The Curt Class III trailer hitch for your Pathfinder, part #C13126 would utilize nuts that are welded up into the frame member. The conical toothed washers used in the installation do a good job of maintaining the torque applied to the bolt during…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Hi Richard! Yes, the Curt Trailer Hitch Receiver #C37RV will fit your 2026 Santa Fe Hybrid. The installation process will be the same. We actually installed this on a 2025 hybrid so you can use that as a guide. I attached a link to the video further…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How Does Washer Face when Installing Curt Hitch # C13146

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching