Tuson Motor Recommendation for Lippert Ground Control 2.0

Question

Question:

241795 tuson leveling motor. will this work with the leveling 2 system?

asked by: STEVE F

1

Helpful Expert Reply:

Yes, I checked with Lippert and for the Ground Control 2.0 the correct motor is the Tuson motor part # LC241795 that you referenced.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The gearbox #RVLG-RDBOX for the Landing Gear Set w/ Handle #RVLG-8HDL can be mounted in the horizontal or vertical position. I went out to the warehouse and tested both the gearbox and lead leg together and the pins that hold the gearbox in place…

view full answer...

Answer 2

Hi James; the better option would be the Bulldog #BD500162 you were looking at. You can add the Motor and Switch Kit for Stromberg Carlson Landing Gear #LG-217884 to the Bulldog which will give it the same functionality as the #LG-4 while saving you…

view full answer...

Answer 3

That motor is the Replacement Motor with Clutch for Lippert Ground Control 2.0 Electric Leveling System #LC241795. The Lippert Ground Control System was replaced by the 3.0 system. The 3.0 system uses a different style of motor and is not compatible…

view full answer...

Answer 4

In previous interactions we have found the 2010 Keystone Laredo 5th wheels to use Venture VMC900 landing gear. This would give you the Replacement Follow Leg #LC119101. I do recommend verifying this is the correct leg for you by measuring your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Tuson Motor Recommendation for Lippert Ground Control 2.0

Product Page this Question was Asked From

Continue Researching