How to Uninstall the Edge Diesel Evolution CTS3 Performance Tuner

Question

Question:

I sold my programmer but it is not working I need to know do you know how to uninstall it Edge evolution CTS two on my Chevrolet Silverado 08

asked by: Eric

0

Expert Reply:

You will need to perform the "factory reset" feature on the Edge Diesel Evolution CTS3 Performance Tuner part # EP69YR in order to reinstall on another vehicle.

In order to reset the tuner back to stock you will need to plug the tuner into your vehicle's OBDII port and allow the tuner to turn on. Then follow these steps.

Step 1: Enter the Quick Link menu

Step 2: Press the Settings icon

Step 3: Scroll through the list and select Factory Reset

Step 4: Press YES

In order to reset your 2008 Chevy Silverado back to stock you will again need to plug the tuner into your vehicle and allow it to power on. Then follow these steps:

1: Go to the Quick Link Menu

2: Click on "Performance Tuning"

3: Select "Level 0"

4: Step 4: Press YES

expert reply by: Conner L

0

Billy J.

8/8/2020

I sold my other truck so I don’t have it anymore and I want to hook it to my 2019 f150.what do I need to do to get it hooked up to new truck?

Jon G.

8/18/2020

If you no longer have the original truck the Edge tuner was installed on then you're going to need to reach out to Edge directly so they can help you get the tuner set up for a new truck. https://edgeproducts.com/

Kyle

12/7/2020

@JonG edge cts2 gas is married to another truck, truck is long gone but still married. Is there a hard reset I can do to be able to marry it to a different truck?

Jon G.

12/8/2020

@Kyle Great question! You'll actually still need to reach out to Edge directly as they are the only ones who can do a hard reset like what you're talking about.

Answer 1

I talked with the vendor about unmarrying the Edge CTS3 Tuner. You will need to go into the tune menu and look for 'return to stock' or 'backup'. This will walk you through the necessary steps to return your truck back to factory tune…

view full answer...

Answer 2

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 3

In order to factory reset an Edge Gas Evolution CTS3 Performance Tuner #EP59YR you will need to go through the following steps. 1. Enter the Quick Link menu. 2. Press the Settings icon. 3. Scroll through the list and select "Factory Reset".…

view full answer...

Answer 4

For the Edge CS Evolution Tuner you will need to enter the programming menu. You will turn on your vehicle without starting it. Then use the Menu button to open the main menu and scroll down with the arrow to the Programming on the screen. From here…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How to Uninstall the Edge Diesel Evolution CTS3 Performance Tuner

Product Page this Question was Asked From

Continue Researching