Replacement Landing Gear Legs for a 2004 Keystone Montana 5th Wheel Trailer

Question

Question:

I have a 2004 30 Keystone Montana 5th wheel. I need to replace the front Landing legs. I could not find a part # on the legs. But on top of the motor I found a data plate. Lippert Components Inc. Part No. M-9000-PK 12VDC-30 Amp Ignition Protected manufactured by Venture Ser. No. 9000-020193 I dont see that you have a 9000 LB legs. I am assuming that the 9000 on the part number means 9000lb.

asked by: Kent

0

Expert Reply:

The Keystone Montana 5th wheel trailers use special landing gear legs. The lead leg is # LC178653 and the follower is # LC178652. Apparently, these legs have a specific bracket spacing and outer tube height combination that is unique to Montana 5th wheel trailers.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 2

There are a few things that go into making sure you choose the correct replacement landing gear. First you need to be sure that the landing gear is rated properly. If you check out the weight rating on your current landing gear just make sure the…

view full answer...

Answer 3

I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the…

view full answer...

Answer 4

Hey Bob, Landing gear components aren't all interchangeable between brands so I'd need to know the exact model to find replacement parts for your current system. If you're just wanting to replace the landing gear as a whole then I'll…

view full answer...

Answer 5

If you take a look at the picture I have included you will see several measurements on a landing gear leg. If your existing landing gear jack legs match then it has the standard spacing so #RVLG-8000 with motor #LC142178 is a great option that…

view full answer...

Answer 6

Hi Shaun, I can definitely help with that. From what we typically see on the 2020 Forest River Wolfpack 365PACK16, the most common landing gear setup is the Lippert/Venture style system with 33-1/2 inch outer tubes and 15-1/2 inch inside-to-inside…

view full answer...

Answer 7

What I think you are saying is that you need new landing gear for a 1997 5th wheel and the currently installed set is 33-3/4" in length. To determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the…

view full answer...

Answer 8

The only difference between the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-8HDL that you mentioned, and the Landing Gear Set #RVLG-8000 is that #RVLG-8HDL comes with the handle, whereas if you were to go with…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

If your thermostat has a heat setting it's typically for the heat pump, but you can quickly tell by looking at the connector of of the rooftop unit to the zone controller. If it's a 6-pin then it doesn't have a heat pump, but if it's…

view full answer...

Replacement Landing Gear Legs for a 2004 Keystone Montana 5th Wheel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching