Atwood Landing Gear Motor Compatibility with Stromberg Carlson Landing Gear Set

Question

Question:

can i use my motor off of my atwood landing gear on your lg-183708

asked by: Al

0

Expert Reply:

The Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs # LG-183708 will allow you to use your Atwood landing gear motor. You may be interested in the spring mounted pull pins # LG-119113 to make leveling faster and easier with this system.

expert reply by: Jason S

0

Answer 1

The Atwood motor 71113 has been discontinued. The motor is a basic landing gear motor and we've been able to confirm the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 is the correct replacement. I've attached a…

view full answer...

Answer 2

I have included a picture that shows how the switch #LG-145236 will attach to the motor and battery. The switch pink wire will go to the positive battery terminal. Then there is a black wire for the ground that will go to the negative battery…

view full answer...

Answer 3

The Replacement Switch for Stromberg Carlson Electric Landing Gear #LG-145236 has the wiring colors you specified and will connect in the manner shown in the attached photo. The pink will connect to the positive battery terminal. The short black will…

view full answer...

Answer 4

Hey Johnny, thanks for reaching out! I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 as a replacement for your 8532-07 motor. According to my research your motor is rated for 5,500 lbs so this motor will…

view full answer...

Answer 5

To replace your current 125340 motor, you will need the #LG-142178. This will be a direct replacement for your current motor, but you may consider replacing the gear box as well. For that you will need the #LG-179015. These together should get…

view full answer...

Answer 6

It sounds like the new higher-capacity Stromberg Carlson motor #LG-196308 you're using is drawing more power than your old motor did. It is likely that your wire gauge and/or fuse value are inadequate for the extra current drawn by the…

view full answer...

Answer 7

Since the gears work easily when not under load and you are able to manually assist the motor when under load, the gears are not the issue. It sounds like the clicking is a relay that is tripping and resetting so it sounds like either the wiring or…

view full answer...

Answer 8

The Bulldog landing gear part #BD500162 that you referenced would be a great choice to use as a replacement for your Atwood setup as they are both made to the same dimensions so these would bolt right up. You are correct that Atwood is no longer in…

view full answer...

Answer 9

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 10

It could be some internal parts but it could also be the electrical system itself. The easiest way to know if the internal parts are the issue or not is to use the manual override to see if it will extend and retract without any electricity. If it…

view full answer...

Answer 11

Both the Replacement Motor #LG-196308 and #LG-142178 have the same mounting dimensions but, like you said the 196308 has a higher weight capacity at 6,500 lbs. The only other notable difference is that the 142178 has a motor speed of 5,500 rpm while…

view full answer...

Answer 12

We've checked in the past and have been told the only current landing gear motor that can be used with your Atwood setup is the part #LG-142178 which even having a lower capacity will still do a great job. The jack motor doesn't support the…

view full answer...

Atwood Landing Gear Motor Compatibility with Stromberg Carlson Landing Gear Set

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching