Where Do the Wires of the Landing Gear Switch # LG-145236 Run

Question

Question:

I need to know where the wires on the Stromberg Carlson #LG-145236 connect? I was replacing gears on landing legs and pulled wires from the switch! thank you.

asked by: Bill

0

Expert Reply:

I have included a picture that shows how the switch # LG-145236 will attach to the motor and battery. The switch pink wire will go to the positive battery terminal. Then there is a black wire for the ground that will go to the negative battery terminal and ground to the trailer frame. The red wire will attach to the red wire on the motor and the other black wire to the black wire on the motor.

expert reply by: Jameson C

0

click to enlarge

John

4/28/2020

I ordered a motor the #is331653 and ordered a switch and the# lg-145236. And I’m having problem keeps blowing the fuse.I have made sure that the wires are correct.pink to + short black wire is to - . Long black wire &amp red mach on the motor .what am I doing wrong.

Chris R.

4/30/2020

The wiring seems to be correct so I'm not sure what the issue could be here. I'm sure you've done this but if not, inspect the rest of your existing wiring just to be sure there aren't any exposed/frayed sections that need to be replaced or any loose connections, both of which could cause a short (and blow a fuse). Also make sure the battery is still in good condition and fully charged. Let me know what you find and we'll go from there.

Answer 1

The Replacement Switch for Stromberg Carlson Electric Landing Gear #LG-145236 has the wiring colors you specified and will connect in the manner shown in the attached photo. The pink will connect to the positive battery terminal. The short black will…

view full answer...

Answer 2

The Atwood motor 71113 has been discontinued. The motor is a basic landing gear motor and we've been able to confirm the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 is the correct replacement. I've attached a…

view full answer...

Answer 3

The Bulldog landing gear part #BD500162 that you referenced would be a great choice to use as a replacement for your Atwood setup as they are both made to the same dimensions so these would bolt right up. You are correct that Atwood is no longer in…

view full answer...

Answer 4

The Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs #LG-183708 will allow you to use your Atwood landing gear motor. You may be interested in the spring mounted pull pins #LG-119113 to make leveling faster and…

view full answer...

Answer 5

Hey Johnny, thanks for reaching out! I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 as a replacement for your 8532-07 motor. According to my research your motor is rated for 5,500 lbs so this motor will…

view full answer...

Answer 6

To replace your current 125340 motor, you will need the #LG-142178. This will be a direct replacement for your current motor, but you may consider replacing the gear box as well. For that you will need the #LG-179015. These together should get…

view full answer...

Answer 7

It sounds like the new higher-capacity Stromberg Carlson motor #LG-196308 you're using is drawing more power than your old motor did. It is likely that your wire gauge and/or fuse value are inadequate for the extra current drawn by the…

view full answer...

Answer 8

Since the gears work easily when not under load and you are able to manually assist the motor when under load, the gears are not the issue. It sounds like the clicking is a relay that is tripping and resetting so it sounds like either the wiring or…

view full answer...

Answer 9

There are two switches on the Electric A-Frame Tongue Jack #JET-3555 that you referenced. One is for the light and one is for raising and lowering the jack. Check out the review video I attached as well.

view full answer...

Answer 10

Lippert actually made a unique landing gear system for your 2007 Montana 5th Wheel Trailer. For the replacement Lead Leg you will use #LC178653 and for the Follow Leg you will use #LC178652. To replace the motor you will need the Stromberg Carlson…

view full answer...

Answer 11

I can give you some information to help you determine if the Lead #LC179013 and Follow #LC179014 legs will fit your 2004 Arctic Fox 29.5E 5th wheel, but we don't really have a database to pull from when it comes to OEM part numbers on trailers.…

view full answer...

Answer 12

Yes, the Replacement Motor for Stromberg Carlson Electric Landing Gear #LG-142178 has been confirmed to replace the ADTH 1RV-200 landing gear motor you currently have so it would work for you.

view full answer...

Where Do the Wires of the Landing Gear Switch # LG-145236 Run

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching