Available Bracket to Mount on a Curt Round Tube Hitch to Mount Vehicle Wiring Harness

Question

Question:

I have a round tube Curt hitch. Will this bracket work with round tubing?

asked by: Matt G

1

Helpful Expert Reply:

The Curt No-Drill Bracket for 6 -Way or 7-Way round Trailer Connectors, # C57202, would be your best option to mount to a round tube trailer hitch.

This bracket uses a hose clamp to allow you to mount the round tube of your trailer hitch.

expert reply by: Jared P

1

Answer 1

If I had to pick a roof rack for a naked roof application, I would stick with Yakima or Thule. I have more confidence in their roof rack fits. My roof rack recommendation is the Yakima roof rack with round crossbars. It will consist of the following:…

view full answer...

Answer 2

Hey Matthew, is there anyway to get 5 lbs out of the kayaks? The highest rated lift assist kayak carrier is the Yakima ShowDown #Y04081 which is rated for up to an 80 lb kayak. Otherwise you'd have to go with a J-style carrier like the etrailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Available Bracket to Mount on a Curt Round Tube Hitch to Mount Vehicle Wiring Harness

Product Page this Question was Asked From

Continue Researching