Confirmation of Draw-Tite Trailer Hitch Receiver on a 2018 Audi SQ5

Question

Question:

Hello, I read the Q and response on the SQ5 Indicating that Item # 76183 is the correct hitch for the 2018 AUDI SQ5. I have attached a photo of the factory hitch and 76183 looks nothing like it. Any comments on this? Thank you

asked by: Dean B

0

Expert Reply:

An aftermarket trailer hitch receiver, like the Draw-Tite # 76183 that is confirmed to fit the 2018 Audi SQ5, are often not designed to install or match a factory hitch receiver.

In fact, sometimes when two different manufacturers offer an aftermarket hitch receiver for a specific vehicle, their designs can be completely different from one another.

expert reply by: Charles S

0

click to enlarge

Answer 1

It doesn't look like we have had a chance yet to install the etrailer Trailer Hitch Receiver part #e94CR on a 2020 Audi Q5 yet so I don't have any specific measurements for you. That said, based on the install photos we have of this and the…

view full answer...

Answer 2

I'd recommend going with the #e94CR Class III hitch for your 2021 Audi Q5. As you can see in the provided photo, the hitch receiver sits pretty tight to the furthest most surface of the back bumper, it doesn't stick out so far that banging…

view full answer...

Answer 3

I have the perfect hitch solution for your 2024 Audi Q5, James! The Stealth Hitches Hidden Rack Receiver #391AUDQ518 gives you a 2" removable receiver so you gain access to a wide variety of accessories while also maintaining an OEM look on your…

view full answer...

Answer 4

The Stealth Hitches Rack Receiver part #391AUDQ518 which is a fit for a 2018 Audi Q5 will not require any cutting or trimming so long as you have the factory center knock-out panel. The 2018+ models should all have the factory center knock-out panel…

view full answer...

Answer 5

You can install Draw-Tite hitch #76183 on your 2018 Audi SQ5 with only minor trimming of the rear fascia. If you refer to the linked photo taken from the included instructions you'll see the small 2 x 3-1/2-inch notch to be made. Just take care…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Confirmation of Draw-Tite Trailer Hitch Receiver on a 2018 Audi SQ5

Continue Researching