Could A-Frame Trailer Coupler # CA-5100-Z be Bolted On

Question

Question:

Can you drill holes into the coupler to attach it to the frame? My old one was bolted on.

asked by: Terry

1

Helpful Expert Reply:

There really is no reason you couldn't bolt on the coupler part # CA-5100-Z but there isn't a recommended way to do so. Best option would be to drill several holes spaced evenly on the a-frame portion of the coupler to the trailer frame. You'd want to use Grade 5 or higher hardware too.

expert reply by: Jameson C

1

Answer 1

The Sleeve-Lock A-Frame Trailer Coupler - Flip Latch - Black - 2-5/16" Ball - 12,500 lbs #CA-5296-B you were looking at is designed to be welded on and as you noticed, does not have the bolt holes available. Instead I recommend going with the…

view full answer...

Answer 2

Yes you can absolutely use the ultimate trailer jack #322-RDJ-2K to replace an older ram jack. The dimensions for the mounting plate are standard and should be the same. The bolt holes are oval slots each having a 3 inch on center measurement. They…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hi Fred! The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F24XV will indeed fit your 2025 Ram 2500 with the factory puck system. The only vehicles it won't fit are ones that have the factory…

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 12

Hey, Michael! Thanks for reaching out. Yes, we do carry a front mount hitch for your 2025 Ram 2500 diesel. The EcoHitch Hidden Front Mount #EH37FR will fit both diesel and non-diesel models, but it will not fit the Power Wagon models. There’s no…

view full answer...

Could A-Frame Trailer Coupler # CA-5100-Z be Bolted On

Product Page this Question was Asked From

Continue Researching